|
|
|
||
|
|
|
|
|
Used
Robots - Robotic Indexing Turntables
|
1
ea RC505001 "2003" Panasonic 3 Axis Model ISP
Cartesian Robotic Tig Welding Cell. Initially powered up in
November 2003 this cell was used off and on for approximately
8 months before the application was discontinued. This
Panasonic Model ISP Cartesian Robot, has approx. 43" (x)
horizontal movement, 15" (y) vertical movement and
21" (z) horizontal movement. There is also a 2 axis
clamping fixture or tooling table. The complete welding
package on this cell includes Two (2) Water Cooled Tig Torches
with manual adjustable separation of the torch holders on one
axis, Two (2) Panasonic YC-500WX4 Power Supplies completely
integrated with all regulators, hoses, cables etc. Water
supply required. The welding cell is 75" wide x 103"
high x 145" deep and has a complete safety package
including, Powered Safety Screen, Light Package, Front
Operating Control and Palm Buttons. This cell could be changed
to the Mig welding process. This is a late model, low hour,
system in Excellent Condition
1 ea RC505002 "2003" Panasonic 4 Axis Model ISP Cartesian Robotic Tig Welding Cell. Initially powered up in November 2003 this cell was used off and on for approximately 8 months before the application was discontinued. This Panasonic Model ISP Cartesian Robot, has approx. 17 1/2" (x) horizontal movement, 10" (y) vertical movement and 15" (z) horizontal movement. The Fourth Axis is a Rotating Wrist movement for the Torch Holding Device. This Cell also includes a Horizontal Moving Fixture/Tooling Table Integrated with the Robot from the Load/Unload position to the Robotic Welding Position. The Complete Welding Package on this cell includes one (1) Panasonic YC-300WX4 Power Supply and One (1) Water Cooled Tig Torch completely integrated with all cables, hoses, etc. Water supply required. The welding cell is 75" wide x 103" high x 126" deep and has a complete safety package including, Powered Safety Screen, Light Package, Front Operating Control and Palm Buttons. This cell could be changed to the Mig welding process. This is a current model, low hour, system in Excellent Condition! 1 ea RC505004 "2003" Panasonic Robotic VR-008 GII, 6 Axis Tig Welding Cell. The Fixture/Tooling Platform is on an Integrated Horizontal Travel Part Presentation Carriage with 26" of Movement from the Load/Unload Station. This system provides maximum operator access for load/unloading and increased productivity. The Complete Welding Package on this cell includes one (1) Panasonic YC-300WX4 Power Supply, One (1) Water Cooled Tig Torch complete with all cables, hoses, etc. Water supply required. The welding cell is a completely enclosed 102" wide x 103" high x 172" deep structure with side access doors and a complete safety package including, Powered Safety Screen, Light Package, Front Operating Control and Palm Buttons. This is a Current Model, Low Hour System, in Excellent Condition! 1 ea RC505005 "2003" Panasonic VR-008 GII Robotic, 6 Axis Tig Welding Cell. This is a larger, panel constructed, Robotic welding Cell with a large Fixture/Tooling table that has approx. 78" of in and out movement between load and welding stations. The Complete Welding Package on this cell includes one (1) Panasonic YC-300WX4 Power Supply, One (1) Water Cooled Tig Torch complete with all cables, hoses, etc. Water supply required. This Welding Cell accommodated this Panasonic VR-008 GII Robotic System and the "2003" Motoman UP-50 listed and priced separately below. See the picture of this larger panel constructed cell for approximation of size. This is a Current Model, Low Hour System, in Excellent Condition! Price includes Panel Constructed Cell. 1 ea R510001P Motoman Model YRFL-NND10G 6-Axis Robot. 22 lb Payload Capacity. Robot Controller NOT Included. "1986" Serial #RH9963-6047-8 "As-Is" Only 1 ea R510011P Miller/OTC Model MRV-6 6-Axis Welding Robot. 13.2 lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1 Control Cabinet. Welding Equipment NOT Included. "1991". 190-575 Volt. Serial #KB168739 "As-Is" Only 1 ea R510012P Miller/OTC Model MRV-6 6-Axis Welding Robot. 13.2 lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1 Control Cabinet. Welding Equipment NOT Included. "1992". 190-575 Volt. Serial #KC301838 "As-Is" Only |
1 ea RP004001 ABB/Esab Orbit 160B,
Robotic Positioner. Two Station Articulating Positioner, for
Load & Weld Station. 353 lbs Each Side, Table Rotation 90
Deg. in 2.7 Sec. Or 360 Deg. in 6.8 Sec., Tilting Arm: Turning
Speed 0 to 11.8 RPM, Indexing 90 Deg. 2.7 Sec., 360 Deg. 7.2
Sec., Station Interchange 3.5 Sec. This unit was integrated to
ABB/Esab a IRB 6L2 Robot. Pos. Ser.#414 441 9034, Cont. 443 440
9005
1 ea RP307001 Aronson Ride-5, Double Ended Tilt and Rotate Robotic Indexing Positioner. This Two-Station Tilt/Rotate Positioner has a Capacity of 500 lbs per Table @ 6" C.G. Tilt and 3" C.G. Rotation. 180 Degree Sweep in 7 Seconds with .0001 Repeatability. Two 18" Diameter Tables with Slots. 8 Non-Adjustable Index Stops for the Table Rotational Axis. 4 Non-Adjust6able Index Stops for the Tilt Axis. Can be Connected to any Robot with Compatible I/O. This is an Indexing Type System, Not Servo. Serial #843 Good Condition 1 ea RP210003P Koike-Aronson RHS10/T2.5-30SD Robotic "Skyhook" Positioner. 2500 lb Load Capacity. Center of Gravity 28". Overhang 3". Off-Center 38" Table. Backlash Control and "Zero" Indicator on Control. "Skyhook" Positioners Provide Part Rotation in Two 360 Degree Axis which Result in Partial or Full Inverting of the Work piece. Serial #869 Very Good Condition 1ea RP207001 Preston-Eastin Model DEPA-30FBRobotic Positioner. . Two Station Articulating Positioner, for Load & Weld Station. 3,000 lb Capacity @ 6" C.G. Each Side. Fixed Table Height of 48" with the Table Flat. 43" x 43" Square Work Tables. Servo Drive that can be Installed on any Robotic System with the Proper Relays. "1996" Serial #DEPA-30FB-187 Very Good Condition 1 ea RP309001P Koike-Aronson "1994" Model #RDCG/T6-100/26SD "Drop-Center" Positioner. Tilt Capacity of 6600 lbs @ 24" from the table, or 4000 lbs @ 57", or 2000 lbs @ 90"!!. Rotation Capacity of 6600 lbs @ 20" Center of Gravity off of the centerline of rotation. Inside Distance Between Upright Sides is 101-3/4" Both Tilt and Rotation Axis have Adjustable Anti-Backlash Dual Pinions on Bull Gears! Both Axis are Servo Drive Variable Speed with Encoders and Resolvers. 360 deg. Rotation @ 0.0-2.0 RPM, 200 deg. Tilt @ 0.0-1.75 RPM. (This Servo Drive Positioner can be converted to a Manual Pendant Operated Machine). Table is 48" x 48" with Hydraulic Master Clamping System for Slave Pallet Mounted Tooling 1 ea. slave included . Note; "Drop Center Positioners" are typically used for work pieces with longer Center of Gravity distances from the table, resulting in lower working or welding heights than using higher capacity positioners. This 1994 Machine has NEVER BEEN USED! Brand New Condition! 1 set RH412002 Koike-Aronson RHS-4.5SD/RTS-4.5 , 9000 lb Robotic Head /Tailstock Positioners. Capacity 9000 lbs @ 6" C.G. Eccentric Load. Headstock capacity only 4500 lbs @ 12" C.G. This 1993 set of Head/Tailstocks were made for Servo Drive Motors and have an Auxiliary Electric Brake on input shaft of gearbox that operates when motor is de-energized. The Servo Drive Motors have been removed , Robotic User would want to install a Servo Drive Motor to match the Robot’s Drive System. These Machines have Backlash Control of spur bull gear driven by Two pinions. Backlash within +/- .0005" per inch of radius. Table 30" x 30" Sq. with 8-1/2" Thru hole on both Head and Tailstock for air, electric, hydraulic fixture access. Ser. #’s 9311 & 936. Very Good Condition! 1 ea H508003 Ransome Model 4H/4T 12,000 lb Headstock/Tailstock. 12,000 lb Capacity @ 6" C.G., Constant Speed Rotation at .52 RPM. 48" Square Tables with Slots. 40" to the Center of the Rotational Axis. 230/460 Volt Input. Serial #5116740 Good Condition 1 ea. M404001 Precision 9’ x 9’ x 27-1/2’ Heavy Duty Manipulator/Travel Car System. This system was manufactured for the Robotics Industry for precision welding on military vehicles. Heavy Duty Mast has 9 ft. of constant speed of precision screw driven lift starting at approx. 36" from the floor to 144" high under the boom. The mast has manual rotation with lock. Boom has 9 ft. of "Dual Pinion" variable speed gear drive and rolls on Thompson Roundway roller system. Weight capacity approx. 750 lb. Travel car is 5’ x 5’ x 19" High and Variable Speed Rack & Pinion Drive on 33 ft. of Thompson Roundway Precision Track. All three (3)-axis paths are accordion booted. This system is now Servo driven. We will change to Pendant AC-Inverter or D.C. Drives. Very Good Condition |
Used Welding Positioners
Contact
We accept VISA, Master Card and American
Express
Web Site Inventory Links Page
Welding Positioners | Welding Manipulators | Seam Welders | Tank Turning Rolls | Turntables
Headstock Tailstocks | Cutting Machines | Robotic Equipment | Miscellaneous Used Welding Equipment
Products Page | Welding Side Beams | Used Welders | E-Mail | Links Page | Welding Rotators | Site Map
sales@usedweldingpositioners.com
