USED WELDING
POSITIONERS
1 ea P810022 Aronson B-200 Bench
Mount Manual Positioner. 200 lb capacity @ 12 c.g., 360 degree
manual rotation with friction breaking. 360 degree manual tilt with
friction breaking. 360 degree manual revolving base. 6 diameter
round table. 12.5 height Serial #93873 Good Condition
1 ea P810013 Aronson AW-300A
Positioner. 300 lb capacity @ 12 c.g.. .2 to 6.0 RPM variable speed
rotation. 360 degree manual tilt with brake and 45 degree pin lock
indexing. 8 diameter round table. Forward/stop/reverse foot pedal.
Pendant control. 120 volt. Serial #510-90179 Good Condition
1 ea P810014 Aronson AW-300A
Positioner. 300 lb capacity @ 12 c.g.. .2 to 6.0 RPM variable speed
rotation. 360 degree manual tilt with brake and 45 degree pin lock
indexing. 8 diameter round table. Forward/stop/reverse foot pedal.
Pendant control. 120 volt. Serial #n/a Good Condition
1 ea P810031 Aronson AW-300A
Positioner. 300 lb capacity @ 12 c.g.. .2 to 6.0 RPM variable speed
rotation. 360 degree manual tilt with brake and 45 degree pin lock
indexing. 8 diameter round table. Forward/stop/reverse foot pedal.
Pendant control. 120 volt. Serial #n/a Good Condition
1 ea P411006 WMP 300 lb
Positioner. 300 lb Load Capacity. Constant Speed Rotation. 90 Degree
Manual Tilt. 24 Fixed Height. 18 Diameter Table w/ Slots. On/Off
Foot Pedal. 230/460 volt. Serial # N/A As Is Only!! Good Working
Condition
1 ea P994007 Standard Machine Co.
Positioner. Approx. 400# Capacity Power Hyd. Tilt, Variable Speed
Rotation. 13 Dia. Table w/ Slots. Fixed Height of 26 Ctr line of
Rotation. AS IS ONLY
1 ea P810015 Aronson BT-500
Positioner. 500 lb capacity @ 12 c.g.. .33 to 10.0 variable speed
rotation by a Grahm drive. 360 degree manual rotation with brake. 6
diameter round table. Forward/stop/reverse foot pedal. 120 volt.
Serial #5348 Good Condition
1 ea P407002 Pandjiris Alpha 5-V8
Positioner. 500 lb cap. @ 3" C.G., 90 Degree Manual Tilt with Pin
Locks in 12.5 Degree Increments. Variable Speed Rotation from .27 to
6.70 RPM. 20.5" Fixed Height to the Center of the Rotational
Axis. 18" Diameter Round Table w/ Slots. On/Off Foot Pedal.
Serial #800-2073-2 Good Condition
1 ea P9911008 Aronson BT-500A
Welding Positioner. 500 lb Cap. Variable Speed, Manual Side Arm Tilt,
8 Dia. 3-Jaw Chuck, Needs Vert. Mtg. Pipe. Foot Controls,
Ser.#77785 Good Condition
1 ea P205004 Jetline Model ZB-500A
Positioner. Capacity of 500 lbs @ 4". Variable Speed Rotation.
Manual Hand Wheel Tilt. 24" Diameter Table. Good Condition
1 ea P409001 Ransome/Worthington
5P Positioner. 500 lb Capacity @ 6 C.G., Power Tilt, Variable Speed
Rotation from .05 to 2.0 RPM. Manual Adjustable Table Height from
32-1/2 to 50-1/2. On/Off Foot Pedal. Includes a 12 Capacity
3-Jaw Self Centering Chuck. Serial #54055 Good Condition
1 ea P904002 Teledyne Readco Model
UPC-5 Positioner. 500 lb capacity @ 6" C.G.. Manual hand wheel
tilt, Variable speed rotation from .040 to 2.0 RPM. Manual adjustable
table height from 25" to 55" in 6" Increments. 26"
round table with slots . Pendant control. On/Off Foot Pedal. 115 volt.
Serial #15256 Good Condition
1 ea T309002 Kistler / Pandjiris
Model U-150 / U-150H Pipe Positioner with Clamping Roller System.
1" - 8" Clamping Range. 660 lb Horizontal Weight Capacity.
330 lb Vertical Weight Capacity. Variable Speed Rotation from 0 to 50
IPM. With Optional #151 Cart and Forward / Stop / Reverse/Variable
Speed Rotary Foot Drum Control. An Excellent System for Flange and
Elbow Welding on Small Diameter Pipe. 115 Volt. Good Condition
1 ea P907002 Pandjiris
7.5-4MVRMT-VPL 750 lb Powered Elevation Positioner. 750 lb capacity @
4 c.g., 135 degree constant speed power tilt. Variable speed
rotation from .19 to 5.8 rpm. 14 constant speed powered elevation
from 34 to 48. 18 diameter round table with slots. Pendant
control. Variable speed foot pedal. 115 volt. Serial #10845E00-5 Good
Condition
1 ea. P411003P Aronson HD10B-PTVR2
Positioner. Capacity 1,000 lbs @ 6" C.G. Variable Speed Rotation
from .07 to 2.0 RPM. With a 10 Turn Potentiometer. 135 Degree Power
Tilt. Manual Adjustable Heights of 24", 32" and 39".
24" Diameter Round Table with Slots. Pendant Control Serial
#75326 Very Good Condition
1 ea P805026P Aronson Model D-10A
1,000 lb Positioner. 1,000 lb capacity @ 4 c.g.. 135 degree power
tilt. Variable speed rotation from 0.0 to 3.25 rpm. Manual adjustable
height from 17.75 to 32.125 in 7 increments. 24 round
table with slots. Pendant control for all functions. 460 volt. Serial
#8629-1 Good Condition
1 ea P408001 Teledyne Readco Model
UPC-10 Positioner. 1,000 lb Capacity @ 6" C.G.. Power Tilt,
Variable Speed Rotation from .040 to 2.0 RPM. Manual Adjustable Table
Height from 25" to 49" in 6" Increments. 29" Round
Table with Slots. Pendant Control. On/Off Foot Pedal. Serial #104199
Good Condition
1 ea P605016 Teledyne Readco Model
UPC-10 Positioner. 1,000 lb Capacity @ 6" C.G.. Power Tilt,
Variable Speed Rotation from .040 to 2.0 RPM. Manual Adjustable Table
Height from 25" to 49" in 6" Increments. 29" Round
Table with Slots. Pendant Control. On/Off Foot Pedal. Serial #104902
Good Condition
1 ea P906007 Ransome Model 10P
1,000 lb Positioner. 1,000 lb capacity @ 6 c.g., 135 degree
constant speed power tilt. Variable speed rotation from .05 to 2.0
rpm, Manual height adjustment from 30 to 48 in 6 increments,
32 diameter round table with slots. Pendant control. On/Off foot
pedal. 115 volt. Serial #1410531 Good Condition
1 ea P305001 Ransome SW-10A Twin
Axis Positioner. 1,000 lb Capacity @ 6" C.G.. 360 Degree Constant
Speed Powered Side Arm Tilt. Variable Speed Rotation from .06 to 2.0
rpm. 36" Diameter Table with Slots. On/off Foot Pedal. 115 Volt.
Serial #9321389 Good Condition
P806002 Aronson Model HD20A-PTVR-2
2,000 lb Positioner. 2,000 lb capacity @ 6 c.g.. 135 degree power
tilt. Variable speed rotation from .07 to 2.0 rpm. Manual adjustable
table height from 23.75 to 38.75 in 7.5 increments. 24
round table with slots. Pendant control for all functions. 115 volt.
Serial #81976 Good Condition.
1 ea P806003 Aronson Model
HD20A-PTVR-2 2,000 lb Positioner. 2,000 lb capacity @ 6 c.g.. 135
degree power tilt. Variable speed rotation from .07 to 2.0 rpm. Manual
adjustable table height from 23.75 to 38.75 in 7.5
increments. 24 round table with slots. Pendant control for all
functions. 115 volt. Serial #81985 Good Condition
1 ea P803018 Aronson Model HD-25
2,500 lb Positioner. 2,500 lb capacity @ 6 c.g., Power tilt.
Variable speed rotation from .07 to 20 rpm. Manual adjustable table
height from 34.5 to 56.5 in 5 increments. 30 square table
with slots. Pendant control for all functions. Forward / Stop /
Reverse Foot Pedal. 230 or 460 volt. Serial # n/a Good Condition
1 ea P910002 Aronson GE-25 2,500
lb Geared Elevation Positioner. 2,500 lb capacity @ 6 c.g.. Power
tilt. Variable speed rotation from .07 to 2.0 RPM. Powered geared
elevation from 29.5 to 53.5 to the center of the rotational
axis. 36 diameter round table. Pendant control for all functions.
230 or 460 volt. Serial #664 Good Condition
1 ea P510009 Koike-Aronson
HS10BBH/T3-30 "Skyhook" Positioner. 2500 lb Load Capacity.
Center of Gravity 28". Overhang 3". Off-Center 38"
Table. "Skyhook" Positioners Provide Part Rotation in Two
360 Degree Axis which Result in Partial or Full Inverting of the
Workpiece. Pendant Control. Serial #80308 Good Condition
1 ea P510010 Koike-Aronson HS10BBH/T3-30 "Skyhook"
Positioner. 2500 lb Load Capacity. Center of Gravity 28".
Overhang 3". Off-Center 38" Table. "Skyhook"
Positioners Provide Part Rotation in Two 360 Degree Axis which Result
in Partial or Full Inverting of the Work piece. Pendant Control.
Serial #N/A Good Condition
1 ea P304009 Cullen- Friestadt
Model 25, 2500 lb Positioner. 2500 lb cap. @ 6" C.G.. Variable
Speed Rotation by Hand Wheel, Power Tilt,. Manual Adjustable Table
Height. 30" Square Table Pendant Control for Stop Start. Serial #
1090 In Working Cond. AS IS ONLY
1 ea P410003 Heinrichs Gluck H75
Powered Elevation Positioner. 2,500 lb Capacity @ 12 C.G.,
Power Tilt, Variable Speed Rotation. 40 to 64 Power Elevation.
24: Square Table. On/Off Foot Pedal. Serial #D20062740. Ready to
Ship!!!! Reconditioned
1 ea P906003 I.S. 2,500 lb
Positioner. 2,500 lb capacity @ 6 c.g., 135 degree constant speed
power tilt, Variable speed rotation from .05 to 1.6 rpm. Manual
adjustable table height from 34 to 58 in 6 increments. 32
diameter round table. Pendant control. On/Off foot pedal. 115 volt.
Serial #n/a Good Condition
1 ea P906004 I.S. 2,500 lb
Positioner. 2,500 lb capacity @ 6 c.g., 135 degree constant speed
power tilt, Variable speed rotation from .05 to 1.6 rpm. Manual
adjustable table height from 34 to 58 in 6 increments. 32
diameter round table. Pendant control. On/Off foot pedal. 115 volt.
Serial #n/a Good Condition
1 ea P906009 I.S. 2,500 lb
Positioner. 2,500 lb capacity @ 6 c.g., 135 degree constant speed
power tilt, Variable speed rotation from .05 to 1.6 rpm. Manual
adjustable table height from 34 to 58 in 6 increments. 32
diameter round table. Pendant control. On/Off foot pedal. 115 volt.
Serial #n/a Good Condition
1 ea P906011 I.S. 2,500 lb
Positioner. 2,500 lb capacity @ 6 c.g., 135 degree constant speed
power tilt, Variable speed rotation from .05 to 1.6 rpm. Manual
adjustable table height from 34 to 58 in 6 increments. 32
diameter round table. Pendant control. On/Off foot pedal. 115 volt.
Serial #n/a Good Condition
1 ea P906024 I.S. 2,500 lb
Positioner. 2,500 lb capacity @ 6 c.g., 135 degree constant speed
power tilt, Variable speed rotation from .05 to 1.6 rpm. Manual
adjustable table height from 34 to 58 in 6 increments. 32
diameter round table. Pendant control. On/Off foot pedal. 115 volt.
Serial #n/a Good Condition
1 ea P906029 I.S. 2,500 lb
Positioner. 2,500 lb capacity @ 6 c.g., 135 degree constant speed
power tilt, Variable speed rotation from .05 to 1.6 rpm. Manual
adjustable table height from 34 to 58 in 6 increments. 32
diameter round table. Pendant control. On/Off foot pedal. 115 volt.
Serial #n/a Good Condition
1 ea P709005 P & H Model WP-2
2,500 lb Positioner. 2,500 lb capacity @ 6 c.g.. Manual/hydraulic
tilt. Variable speed rotation. Manual adjustable height from 24 to
40 in 6 increments. Pendant control. 230/460 volt. Serial
#WP-2447. Good Condition.
1 ea P609001 Ransome Model 25P
Positioner. 2,500 lb Capacity @ 6 C.G., Power Tilt, Variable Speed
Rotation from .031 to 2.0 RPM. 40 Square Table. Manual Height
Adjustment from 45-1/2 to 57-1/2. Pendant Control. Serial #N/A Good
Condition
1 ea P906023 Worthington Model 25P
Positioner. 2,500 lb Capacity @ 6 C.G., Constant speed power tilt,
Variable speed rotation from .031 to 2.0 rpm. 32 square table.
Manual height adjustment from 39 to 57 in 6 increments. Pendant
control. On/Off foot pedal. 230 or 460 volt. Serial #55984 Good
Condition
1 ea P906027 Worthington Model 25P
Positioner. 2,500 lb Capacity @ 6 C.G., Constant speed power tilt,
Variable speed rotation from .031 to 2.0 rpm. 34 round table with
slots. Manual height adjustment from 37.75 to 55.75 in 6
increments. Pendant control. On/Off foot pedal. 230 or 460 volt.
Serial #35331507 Good Condition
1 ea P406002 Webb 25P, 2,500 lb
Positioner. 2,500 lb Capacity @ 6" C.G., Power Tilt, .15 to 1.5
Variable Speed Rotation. 36" Fixed Table Height. 30"
Diameter Round Table with Slots. Pendant Control. Serial #N/A Good
Condition
1 ea P908006 Aronson HD30-6A
Positioner. 3,000 lb capacity @ 6 c.g., Power tilt, Variable speed
rotation from .07 to 2.0 RPM. Manual adjustable table height from
34.5 to 56.5 in 5.5 increments. 36 square table. Pendant
control. On/Off foot pedal. 230 or 460 volt. Serial #92601
1 ea P410004 Ferguson
16/2-F475-270 Pipe Rotator with Clamping Roller System. 3,000 lb Load
Capacity. 3 to 20 Diameter Capacity. Variable Speed Pipe
Rotation by a Set of 12 Diameter Steel Wheel Turning Rolls with a
Hold Down Devise. Turning Rolls are Mounted on a Constant Speed Side
Arm Table that has 360 Degree Power Rotation. A Unique System for
Welding Off Set Pipe and Pipe Elbows in Any Position. Serial #61418
Good Condition
1 ea P609002 Worthington Model 30P
Positioner. 3,000 lb Capacity @ 6 C.G., Power tilt, Variable speed
rotation from .031 to 1.24 rpm. 45 square table. Manual height
adjustment from 42 to 72in 6 increments. Pendant control.
Serial #36268525 Good Condition
1 ea P805013 Ransome Model 30P
3,000 lb Positioner. 3,000 lb capacity @ 6 c.g., Power tilt.
Variable speed rotation from .03 to 12 RPM. Fixed table height of
38-3/4 to the center of the rotational axis. 40 square table
with slots. Pendant control. 230 or 460 volt. Serial #4840 Good
Condition
1 ea P611020 Aronson Model
HS30GE/T4-62 Sky Hook Positioner. 4,000 lb Capacity @ 36 C.G. Off
of the Turntable Face. 62 Clearance from Center of Turntable.
"Skyhook" Positioners Provide Part Rotation in Two 360
Degree Axis which Result in Partial or Full Inverting of the Workpiece.
Pendant Control. Serial #7914 Good Condition
1 ea P810026 Aronson GE-45 Geared
Elevation Positioner. 4,500 lb capacity @ 12 c.g.. 135 degree power
tilt. .01 to 1.2 variable speed rotation. Powered elevation from 53
to 86. 42 square table with slots. Pendant control. Serial # n/a
Good Condition
1 ea P810018 Aronson X21E Geared
Elevation Positioner. 5,000 lb capacity @ 6 c.g.. 135 degree power
tilt. Variable speed power rotation. Powered elevation from 53 to
77. 48 diameter round table with slots. Pendant control. Serial
#665 Good Condition
1 ea RP309001P Koike-Aronson
1994 Model #RDCG/T6-100/26SD Drop-Center Positioner. Tilt
Capacity of 6600 lbs @ 24 from the table, or 4000 lbs @ 57, or
2000 lbs @ 90!!. Rotation Capacity of 6600 lbs @ 20 Center of
Gravity off of the centerline of rotation. Both Tilt and Rotation Axis
have Adjustable Anti-Backlash Dual Pinions on Bull Gears! Both Axis
are Servo Drive Variable Speed with Encoders and Resolvers. 360 deg.
Rotation @ 0.0-2.0 RPM, 200 deg. Tilt @ 0.0-1.75 RPM. (This Servo
Drive Positioner can be converted to a Manual Pendant Operated
Machine). Table is 48 x 48 with Hydraulic Master Clamping System
for Slave Pallet Mounted Tooling 1 ea slave included. Note; Drop
Center Positioners are typically used for work pieces with longer
Center of Gravity distances from the table, resulting in lower working
or welding heights than using higher capacity positioners. This 1994
Machine has NEVER BEEN USED! Brand New Condition!
1 ea P810001 Aronson 180T120/CC
180 Degree Tilter. 7,000 lb weight capacity @ 12 c.g. from table.
Table tilts 180 degrees from vertical to vertical. For positioning
long work pieces such as long truck frames for down hand welding.
Table does NOT rotate. Table is a dual screw clamping table with an
internal capacity of 40 wide x 27.5 high Very Good Condition
1 ea P805005 Teledyne-Readco Model
UHSE-400 7,500 lb Side Arm Positioner. Side arm positioners are also
known as Skyhook positioners. 7,500 lb capacity @ 6 c.g.. Dual
screw driven powered elevation from 31.5 to 77.5 with the side
arm table flat and parallel to the floor. 51 to the center of the
rotational axis with the side arm at 90 degrees to the floor. Side arm
table is 3.5 off set to the center of the rotational axis on the
headstock. Variable speed rotation of the side arm table. 88
maximum part diameter capacity. Pendant control for all functions. 460
volt. Serial #106130 Good Condition
1 ea P805006 Teledyne-Readco Model
UHSE-400 7,500 lb Side Arm Positioner. Side arm positioners are also
known as Skyhook positioners. 7,500 lb capacity @ 6 c.g.. Dual
screw driven powered elevation from 31.5 to 77.5 with the side
arm table flat and parallel to the floor. 51 to the center of the
rotational axis with the side arm at 90 degrees to the floor. Side arm
table is 3.5 off set to the center of the rotational axis on the
headstock. Variable speed rotation of the side arm table. 88
maximum part diameter capacity. Pendant control for all functions. 460
volt. Serial #106133 Good Condition
1 ea P808011 Aronson GE-90A 9,000
lb Geared Elevation Positioner. 9,000 lb capacity @12 c.g.., 135
degree power tilt. Variable speed rotation from .04 to 1.0 rpm. 33
powered geared elevation from 54.5 to 87.5with the table flat.
42 diameter round table with a 9 diameter thru hole. Pendant
control for all functions. Serial #7019 Good Condition
1 ea P001011 Aronson GE-1200-EXP,
1995 120,000 lb Positioner. This Unique Positioner was Specially
Designed by NASA to Assemble and Float on Built-In Air Pads a 2
Billion Dollar Spacecraft that was Launched in late December 1999. The
Special Features are Numerous and can be seen on our Space Website
www.wpi-space-satellite.com or call Paul Rensing. Excellent Condition
UNIVERSAL BALANCE POSITIONERS
1 ea P804001 Koike-Aronson
C2000-P30 Universal Balance Positioner 1500 lb Capacity @ 12 from
the Table. Variable speed powered rotation from 0.1 to 6.0 rpm.
Adjustable Height from 30 to 36. 8 Diameter Work Table.
Serial #954228 Good Condition
1 ea P810005 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #83299 Good Condition
1 ea P810006 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #75196 Good Condition
1 ea P810007 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #n/a Good Condition
1 ea. P810008 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #n/a Good
Condition
1 ea. P810009 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #n/a Good Condition
1 ea. P810010 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #n/a Good Condition
1 ea. P810011 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #n/a Good Condition
1 ea. P810012 Aronson C-4000
Universal Balance Positioner. 4,000 lb capacity @ 12 from the
table. 360 degree manual rotation. 48 fixed table height. 12:
diameter work table. These are manual balanced machines they are
typically used for weldments that require quick re-positioning such as
boxes, frames, etc.. Serial #n/a Good Condition
USED
CHUCKS
1 ea CH812005 Aronson Model 3JC5
3-Jaw Self Centering Scroll Chuck. 5 maximum outside clamping
capacity. 7 maximum inside clamping capacity. 1-1/4 thru hole.
Serial # n/a Good Condition
USED HEADSTOCK & TAILSTOCKS
1 ea H910001 Jetline 500 lb Bench Top Headstock. 500 lb capacity
@6 c.g.. Variable Speed Rotation. 12 diameter thru hole in the
headstock with a 8-12 diameter chuck with a 12 thru hole. 17
height to the center of the rotational axis. On/off foot pedal. 115
volt. Serial # n/a Good Condition
1 ea H810020 Aronson TS1000 1,000 lb Manual Special Utility
Tailstock. 30 to 45 manual adjustable height to the center of
the rotational axis. 360 degree manual rotation with brake and 45
degree pin lock. 8 diameter table. Serial #80683 Good Condition
1 ea H810021 Aronson TS1000 1,000 lb Manual Special Utility
Tailstock. 30 to 45 manual adjustable height to the center of
the rotational axis. 360 degree manual rotation with brake and 45
degree pin lock. 8 diameter table. Serial #76727 Good Condition
1 ea H100729 Hobart/Motoman 1,000 lb Headstock. 1,000 lb
capacity @ 6 c.g., 47 height to the center of the rotational
axis. 24 diameter round tables. Currently equipped with a servo
motor. Can be converted to a standard operating unit. Serial #89142
1 ea H100720 Hobart/Motoman 1,000 lb Headstock/Tailstock. 1,000
lb capacity @ 12 c.g., 47 height to the center of the rotational
axis. 19.5 diameter round tables. Currently equipped with a servo
motor. Can be converted to a standard operating unit. Serial #89142
1 ea H100721 Aronson RHS-1.0 1,000 lb Headstock. 1,000 lb
capacity @ 6 c.g., 33 height to the center of the rotational
axis. 18 diameter round table with slots. Currently equipped with a
servo motor. Can be converted to a standard operating unit. Serial
#948
1 ea H100722 Aronson RHS-1.0 1,000 lb Headstock. 1,000 lb
capacity @ 6 c.g., 33 height to the center of the rotational
axis. 18 diameter round table with slots. Currently equipped with a
servo motor. Can be converted to a standard operating unit. Serial
#949
1 ea H100725 Aronson RHS-1.0 1,000 lb Headstock. 1,000 lb
capacity @ 6 c.g., 33 height to the center of the rotational
axis. 18 diameter round table with slots. Currently equipped with a
servo motor. Can be converted to a standard operating unit. Serial
#9510
1 ea H100723 Automated Concepts 1,000 lb Headstock/Tailstock.
1,000 lb capacity @ 12 c.g., 32 height to the center of the
rotational axis. 16 diameter round tables. Currently equipped with
a servo motor. Can be converted to a standard operating unit. Serial #
n/a
1 ea H100724 Bobcat 1,000 lb Headstock/Tailstock. 1,000 lb
capacity @ 12 c.g., 30 height to the center of the rotational
axis. 12 diameter round tables. Currently equipped with a servo
motor. Can be converted to a standard operating unit. Serial # n/a
1 ea H606002 Bignall-Keeler Model 8A Dual Sided Headstock. 2,000
lb Weight Capacity. 10 Diameter Thru Hole Chuck Capacity. Variable
Speed Rotation. 44 Fixed Height to the Center of the Rotational
Axis. 230/460 Volt. Serial #5979
1 ea H906016 I.S. 2,500 lb Headstock. 2,500 lb capacity @ 6
c.g., Variable speed rotation from .05 to 1.6 rpm., 29.25 diameter
round table. Fixed height of 45.75 to the center of the rotational
axis. Pendant control. On/Off foot pedal. 115 volt. Serial #n/a Good
Condition
1 ea H906022 I.S. 2,500 lb Headstock. 2,500 lb capacity @ 6
c.g., Variable speed rotation from .05 to 1.6 rpm., 29.25 diameter
round table. Fixed height of 38 to the center of the rotational
axis. Pendant control. On/Off foot pedal. 115 volt. Serial #n/a Good
Condition
1 ea H906030 I.S. 2,500 lb Adjustable Height Headstock. 2,500 lb
capacity @ 6 c.g., Variable speed rotation from .05 to 1.6 rpm.,
36 diameter round table. Manual adjustable height from 25: to 49
in 6 increments to the center of the rotational axis. Pendant
control. On/Off foot pedal. 115 volt. Serial #n/a Good Condition
1 ea H205007 Ransome 3T Tailstock Positioner. 3000 lb cap. @
12" C.G. from Table Surface and 12" Eccentric from Rotation
Center. 40" Square Table with Slots. Serial #63721 Good Condition
1 ea H110316 Aronson Model HS-4 4,500 lb Headstock, 4,500 LB
capacity @ 6 c.g., Variable speed rotation from.04 to 1.2 rpm.
27.75 to the center of the rotational axis. 30 square table with
slots. Pendant control. 230 or 460 volt. Serial #78178 Ready to be
reconditioned to fit your needs
1 ea H110317 Aronson Model HS-4 4,500 lb Headstock, 4,500 LB
capacity @ 6 c.g., Variable speed rotation from.04 to 1.2 rpm.
27.75 to the center of the rotational axis. 30 square table with
slots. Pendant control. 230 or 460 volt. Serial #41499 Ready to be
reconditioned to fit your needs !
1 ea H904009 Pandjiris TS-50 Tailstock Only. 5,000 lb capacity @
12 c.g., Manual rotation. 53 square table with mounting slots.
40 to the center of the rotational axis. Serial #n/a Good Condition
1 ea H912013 Aronson Model HS-6 6,000 lb Headstock. 6,000 lb
capacity @ 12 c.g., .025 to 1.5 ipm variable speed rotation, 48
square table with slots, 36 fixed height to the center of the
rotational axis ( can be increased with a riser ), pendant control,
230 or 460 volt. Serial #99391 Good Condition
1 ea H101008 Aronson Model HS-6 6,000 lb Headstock. 6,000 lb
capacity @ 12 c.g., .025 to 1.5 ipm variable speed rotation, 48
square table with slots, 36 fixed height to the center of the
rotational axis ( can be increased with a riser ), pendant control,
230 or 460 volt. Serial #74165 Ready to be reconditioned to fit your
needs
1 ea H101009 Aronson Model HS-6 6,000 lb Headstock. 6,000 lb
capacity @ 12 c.g., .025 to 1.5 ipm variable speed rotation, 48
square table with slots, 36 fixed height to the center of the
rotational axis ( can be increased with a riser ), pendant control,
230 or 460 volt. Serial #WW392 Ready to be reconditioned to fit your
needs
1 ea H110318 Aronson Model HS-6 6,000 lb Headstock, 6,500 LB
capacity @ 12 c.g., Variable speed rotation from.05 to 1.5 rpm.
27.75 to the center of the rotational axis. 48 square table with
slots. Pendant control. 230 or 460 volt. Serial #72112 Ready to be
reconditioned to fit your needs
1 ea H110319 Aronson Model HS-6 6,000 lb Headstock, 6,000 LB
capacity @ 12 c.g., Variable speed rotation from.05 to 1.5 rpm.
36 to the center of the rotational axis. 48 square table with
slots. Pendant control. 230 or 460 volt. Serial #72115 Ready to be
reconditioned to fit your needs
1 ea H110320 Aronson Model HS-6VA 6,000 lb Headstock, 6,000 LB
capacity @ 12 c.g., Variable speed rotation from.05 to 1.5 rpm.
36 to the center of the rotational axis. 48 square table with
slots. Pendant control. 230 or 460 volt. Serial #72113 Ready to be
reconditioned to fit your needs
1 ea H810017 Aronson TS-6 6,000 lb Tailstock. Fixed height of
36 to the center of the rotational axis. 48 square table with
slots. Serial #7162 Good Condition
1 ea H810016 Aronson TS-10AB 10,000 lb Tailstock. 36 to 66
manual adjustable height in 6 increments. 48 square table with
slots. Serial #79167 Good Condition
1 ea H100715 Aronson Model HS-10SD 10,000 lb Headstock. 10,000
lb capacity @12 c.g., Variable speed rotation from .04 to 1.0 RPM
by a dual pinion drive. 42 square table with slots. 36 height to
the center of the rotational axis. Pendant Control. Serial #0059 Good
Condition
1 ea H100716 Aronson Model HS-10SD 10,000 lb Headstock. 10,000
lb capacity @12 c.g., Variable speed rotation from .04 to 1.0 RPM
by a dual pinion drive. 42 square table with slots. 36 height to
the center of the rotational axis. Pendant Control. Serial #0060 Good
Condition
1 ea H100717 Aronson Model HS-10SD 10,000 lb Headstock. 10,000
lb capacity @12 c.g., Variable speed rotation from .04 to 1.0 RPM
by a dual pinion drive. 42 square table with slots. 36 height to
the center of the rotational axis. Pendant Control. Serial #9952 Good
Condition
1 ea H100719 Aronson Model HS-10SD 10,000 lb Headstock. 10,000
lb capacity @12 c.g., Variable speed rotation from .04 to 1.0 RPM
by a dual pinion drive. 42 square table with slots. 36 height to
the center of the rotational axis. Pendant Control. Serial #9957
Reconditioned and Ready to Ship
1 ea H110321 Aronson Model HS-10 10,000 lb Headstock. 10,000 lb
capacity @12 c.g., Variable speed rotation from .04 to 1.0 rpm.
48 square table with slots. 36 height to the center of the
rotational axis. Pendant Control. Serial #7073 Ready to be
reconditioned to fit your needs
1 ea H110322 Aronson Model HS-10 10,000 lb Headstock. 10,000 lb
capacity @12 c.g., Variable speed rotation from .04 to 1.0 rpm.
48 square table with slots. 36 height to the center of the
rotational axis. Pendant Control. Serial #84376 Ready to be
reconditioned to fit your needs
1 ea H110323 Aronson Model HS-10 10,000 lb Headstock. 10,000 lb
capacity @12 c.g., Variable speed rotation from .04 to 1.0 rpm.
48 square table with slots. 36 height to the center of the
rotational axis. Pendant Control. Serial #7292 Ready to be
reconditioned to fit your needs
1 ea H110324 Aronson Model HS-10 10,000 lb Headstock. 10,000 lb
capacity @12 c.g., Variable speed rotation from .04 to 1.0 rpm.
48 square table with slots. 36 height to the center of the
rotational axis. Pendant Control. Serial #95429 Ready to be
reconditioned to fit your needs
1 ea H110325 Aronson Model HS-10 10,000 lb Headstock. 10,000 lb
capacity @12 c.g., Variable speed rotation from .04 to 1.0 rpm.
48 square table with slots. 36 height to the center of the
rotational axis. Pendant Control. Serial #79253 Ready to be
reconditioned to fit your needs
1 ea H110326 Aronson Model HS-10 10,000 lb Headstock. 10,000 lb
capacity @12 c.g., Variable speed rotation from .04 to 1.0 rpm.
48 square table with slots. 36 height to the center of the
rotational axis. Pendant Control. Serial #n/a Ready to be
reconditioned to fit your needs
1 ea H110327 Aronson Model HS-10 10,000 lb Headstock. 10,000 lb
capacity @12 c.g., Variable speed rotation from .04 to 1.0 rpm.
48 square table with slots. 36 height to the center of the
rotational axis. Pendant Control. Serial #7296 Ready to be
reconditioned to fit your needs
1 ea H102204 Aronson HS-10 GE, 10,000 lb Geared Elevation
Headstock Positioner. Capacity 5 Tons @12 C.G. from Table &
Center of Rotation., Variable Speed Rotation by new AC Inverter
Control. Powered Geared Elevation of 20 to 72 Cent. of Rot. from
Floor. 36 dia. Round Table with 9 Thru Hole. Ser. #695. PMd
by Aronson. Very Good Condition.
1 ea H100727 Fanuc 10,000 lb Tailstock. 10,000 lb capacity @
6 c.g., 44 height to the center of the rotational axis. Air pin
locks at 180 degree. 6.75 diameter table. Serial # n/a As-Is
1 ea H100728 Fanuc 10,000 lb Tailstock. 10,000 lb capacity @
6 c.g., 44 height to the center of the rotational axis. Air pin
locks at 180 degree. 6.75 diameter table. Serial # n/a As-Is
1 ea H805002 Irco Model RHS-10 10,000 lb Headstock. 10,000 lb
capacity @ 12 c.g., Variable speed rotation. Dual pinion drive.
Fixed table height of 72 to the center of the rotational axis.
40 x 41.25 table. Pendant control for all functions. 230 or 460
volt. Serial #12398 Good Condition
1 ea H110212 Ransome 5H 10,000 lb Headstock. 10,000 lb capacity
@ 12 c.g., .52 rpm constant speed rotation. 48 square table with
slots. 72 to the center of the rotational axis. Pendant Control.
230 or 460 volt. Serial #5313103 Ready to be reconditioned to fit your
needs !
1 ea H110213 Ransome 5H 10,000 lb Headstock. 10,000 lb capacity
@ 12 c.g., .52 rpm constant speed rotation. 36 diameter round
table with slots. 72 to the center of the rotational axis. Pendant
Control. 230 or 460 volt. Serial #n/a Ready to be reconditioned to fit
your needs
1 ea H909009P Ransome Model 5T Tailstock. 10,000 lb capacity @
12 c.g., Manual Rotation. 48 square table with slots. Fixed
height of 40 to the center of the rotational axis. Serial #NA Good
Condition
1 ea H101010 Aronson Model HTS-12 Headstock/Tailstock. 12,000 lb
capacity @ 6 c.g., Variable speed rotation from .05 to 1.5 RPM.
36 fixed height to the center of the rotational axis (can be
increased with risers). 48 square tables with slots. Pendant
control. 230 or 460 volt. Serial #6264 Ready to be reconditioned to
fit your needs
1 ea H805017 Aronson Model RVTS12/20GE 12,000 lb Geared
Elevation Tailstock on Variable Speed Travel Car with Track. 12,000 lb
capacity @ 6 c.g.. Constant speed powered geared elevation from
57 to 178 to th center of the rotational axis. Mounted on a
variable speed rack and pinion driven travel car with 46 of track.
Pendant control for all functions. 230 or 460 volt. Serial #n/a Good
Condition
1 ea H1011005 Teledyne-Readco HTS-250, 12,500 lb Headstock
Positioner. Capacity 12,500 lbs @ 12 (25,000 lbs @ 6 with
Suitable Tailstock) Var. Speed Rotation by New AC Inverter Drive. 3 HP
Motor. 54 x 54 Square Table with Tee Slots. Approx. 55 Ctr.
of Rot. from Floor. Ser. # 105836 Good Condition (2-4 wks)
1 ea H805003 IGM System Model RF6000 13,200 lb Tailstock. 13,200
lb capacity @ 6 c.g., Fixed height of 87 to the center of the
rotational axis. 59 diameter round table. 1988 date of mfg.. Serial
#501699 Very Good Condition
1 ea H805004 IGM System Model RF6000 13,200 lb Tailstock. 13,200
lb capacity @ 6 c.g., Fixed height of 87 to the center of the
rotational axis. 59 diameter round table. 1988 date of mfg.. Serial
#501699 Very Good Condition
1 ea H100604 Aronson Model HS-16 16,000 lb Headstock. 16,000 lb
load capacity @ 12 center of gravity. Variable speed rotation from
.02 to .6 rpm. 54 square table with slots. 50 height to the
center of the rotational axis. Pendant control. Serial #75118 Good
Condition
1 ea H810019 Aronson TS-16 16,000 lb Tailstock. Fixed height of
50 to the center of the rotational axis. 54: square table with
slots. Serial # n/a Good Condition
1 ea H805011 Aronson Model RHS-16 16,000 lb Headstock. 16,000 lb
capacity @ 12 c.g., Variable speed rotation from .02 to .60 rpm.
Fixed height of 50 to the center of the rotational axis. 35
diameter mounting ring - no table. Pendant control for all functions.
230 or 460 volt. Serial #9115 Good Condition
1 ea H909005 Aronson HS-16GE Geared Elevation Headstock. 16,000
capacity @ 12 c.g., Variable speed rotation from .02 to .60 rpm by
a dual pinion drive. Powered geared elevation height from 20 to
72 to the center of the table. 36 diameter round table. 230 or
460 volt. Serial #8225 Good Condition
1 ea H508004 Crossroads 90 Degree Indexing Headstock/Tailstock.
20,000 lb Concentric Load Capacity. To Index Part from Flat to 90
Degrees Only in one Direction and then Back to Starting Position.
59 to the Center of the Rotational Axis. Electric/Hydraulic Driven.
230/460 Volt Input. Good Condition
1 ea H100603 Aronson Model HS-20 20,000 lb Headstock. 20,000 lb
load capacity @ 12 center of gravity. Variable speed rotation from
.016 to .5 rpm. 54 square table with slots. 50 height to the
center of the rotational axis. Pendant control. Serial #7129 Good
Condition
1 ea H106005 Aronson Model TS-20 20,000 lb Tailstock. 20,000 lb
load capacity @ 12 center of gravity. 54 square table with
slots. 53 height to the center of the rotational axis. Serial # n/a
Good Condition
1 ea H809014 Aronson HTS-20 20,000 lb Headstock/Tailstock.
20,000 lb capacity @ 6 c.g., Variable speed rotation from .02 to
1.7 rpm. Dual pinion drive. 48 Square tables with an 8.5
diameter thru hole. 36 height to the center of the rotational axis.
Pendant control. 230 or 460 volt. Serial # 9034/9025. Good Condition
1 ea H110333 Aronson HTS-20 20,000 lb Headstock/Tailstock.
20,000 lb capacity @ 6 c.g., Constant speed rotation. 48 Square
tables with slots. 36 height to the center of the rotational axis.
Pendant control. 230 or 460 volt. Serial #98449/98255 Constant Speed
Reconditioned Quick Turn Around ! Converted to Variable Speed
Rotation from .02 to 1.7 RPM!!
1 ea H110334 Aronson HTS-20 20,000 lb Headstock/Tailstock.
20,000 lb capacity @ 6 c.g., Constant speed rotation. 48 Square
tables with slots. 36 height to the center of the rotational axis.
Pendant control. 230 or 460 volt. Serial #98448/98254 Constant Speed
Reconditioned Quick Turn Around !! Converted to Variable Speed
Rotation from .02 to 1.7 RPM!
1 ea H110335 Aronson HTS-20 20,000 lb Headstock/Tailstock.
20,000 lb capacity @ 6 c.g., Constant speed rotation. 48 Square
tables with slots. 36 height to the center of the rotational axis.
Pendant control. 230 or 460 volt. Serial #00459/00271 Constant Speed
Reconditioned Quick Turn Around !! Converted to Variable Speed
Rotation from .02 to 1.7 RPM!
1 ea H110336 Aronson HTS-20 20,000 lb Headstock/Tailstock.
20,000 lb capacity @ 6 c.g., Constant speed rotation. 48 Square
tables with slots. 36 height to the center of the rotational axis.
Pendant control. 230 or 460 volt. Serial #00458/00270 Constant Speed
Reconditioned Quick Turn Around !! Converted to Variable
Speed Rotation from .02 to 1.7 RPM!!
1 set H211007 Teledyne Readco 20,000 lb Headstock/Tailstock.
20,000 lb Capacity @ 6" C.G., Variable Speed Rotation. 53"
Diameter Round Table with Slots. Forward/off/Reverse Foot Pedal.
Headstock is Mounted on a Screw Driven Variable Speed Travel Car on 9'
of Track. Tailstock has a 24" Diameter Through Hole. Pendant
Control for all Functions. Serial #106-633 Good Condition
1 ea H100602 Aronson Model TS-25 25,000 lb Tailstock. 25,000 lb
load capacity @ 12 center of gravity. 60 square table with
slots. 50 height to the center of the rotational axis. Serial
#8182. Good Condition
2 sets H504001&2 Komatsu 25,000 LB Head/Tail Stocks. Cap.
25,000 @ 6 Center of Gravity off of the center line of Rotation.
These Head/Tailstocks were used with a large Robotic Manipulator that
was Welding Earth 20 ft. long Mover Boom Sections. They have Dual
Directional Hydraulic Clamping Devices for holding the fixture or work
pieces. They are designed for large Eccentric Loads and have integral
counter weights. They now have Servo Motors that are 1500 rpm and 2.8
kw. and produce 2.1 rpm. The braking is done by a Hydraulic Disc
Caliper. The Servo Motors can be replaced by an AC Inverter Drive for
Manual Operation AS-IS No Changes. We Change to AC-Inverter Drive with
Pendant Control Variable Speed
1 ea H912005 Ransome Model 6H/6T 32,000 lb Headstock/Tailstock.
32,000 lb capacity @ 6 c.g., Constant speed rotation of .56 RPM
(can be converted to variable speed). 54 square tables with slots.
78 height to the center of the rotational axis. Tailstock is
mounted on a constant speed travel car that runs on 46 machined 60
lb RR track (Not Supplied). 460 volt. Serial #6933357/6933359 Very
Good Condition
1 ea H809025 Aronson HTS-40 40,000 lb Headstock/Tailstock.
40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8
rpm. Dual pinion drive. 54 square tables with an 8 diameter thru
hole. 50 height to the center of the rotational axis. Pendant
control. 230 or 460 volt. Serial # 909/905 Good Condition
1 ea H904003 Aronson HTS-40 40,000 lb Headstock/Tailstock.
40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8
rpm. Dual pinion drive. 36.5 round tables with a 19 diameter
thru hole. 50 height to the center of the rotational axis. Pendant
control. 230 or 460 volt. Serial # n/a Good Condition
1 ea H904004 Aronson HTS-40 40,000 lb Headstock/Tailstock.
40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8
rpm. Dual pinion drive. 36.5 round tables with a 19 diameter
thru hole. 50 height to the center of the rotational axis. Pendant
control. 230 or 460 volt. Serial # n/a Good Condition
1 ea H909002 Aronson HTS-40 40,000 lb Headstock/Tailstock.
40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8
rpm. Dual pinion drive. 36.5 round tables with a 19 diameter
thru hole. 50 height to the center of the rotational axis. Pendant
control. 230 or 460 volt. Serial # 862 Good Condition
1 ea H909003 Aronson HTS-40 40,000 lb Headstock/Tailstock.
40,000 lb capacity @6: c.g., Variable speed rotation from .026 to .8
rpm. Dual pinion drive. 36.5 round tables with a 19 diameter
thru hole. 50 height to the center of the rotational axis. Pendant
control. 230 or 460 volt. Serial #863 Good Condition
1 ea H110328 Aronson HTS-60 60,000 lb Headstock/Tailstock.
60,000 lb capacity @ 6 c.g., .5 rpm Constant speed rotation. 54
square table with slots. 50 height to the center of the rotational
axis. Pendant control. 230 or 460 volt. Serial #7352/n/a Ready to be
reconditioned to fit your needs
1 ea H110329 Aronson HTS-60 60,000 lb Headstock/Tailstock.
60,000 lb capacity @ 6 c.g., .5 rpm Constant speed rotation. 54
square table with slots. 50 height to the center of the rotational
axis. Pendant control. 230 or 460 volt. Serial #7568/7017 Ready to be
reconditioned to fit your needs
USED FLOOR TURNTABLES & TILTING
TABLES
TT204001 Nashville Machine Co.
Indexing Table. Capacity 1,000 lbs @ 6" Center of Gravity. Three
Position Motorized Indexing Table with Air Clamping at Stop Position.
30" Diameter Round Table. 27" to 35" Adjustable Table
Height by a Manual Screw Jack with Pin Locks in 1" Increments.
Warning Buzzer for Rotational Movement. Foot Pedal. 115 Volt. Very
Good Condition
1 ea FT102201 Reliance High Speed
Turntable, with Magnetic Chuck. This is an Unique Variable Speed
Turntable with a Speed Range up to 110 RPM. The 14 Table is a
Magnetic Chuck with a Allen Key operated on/off switch. A Heavy Duty
Unit. Very Good Condition
1 ea TI005005 Hercules 2000 lb
Power Tilting Tables. Model TI-23842. 38 X 42 Table w/16 Lip,
Electro-Hyd. Tilt of Approx. 75 Deg. 115v Input. Very Good Condition
1 ea TT306001 Advanced Lifts 2,000
lb Power Tilting Table. Model UE-290. 54" Long x 48" Wide
two Sided Table. Electric/Hydraulic Tilt of 90 Degrees. 480 Volt.
Serial #23497/1199 Very Good Condition
1 ea FT405002P VMW 100 Ton Floor
Turntable. 200,000 lb Capacity @ 12" C.G., Variable Speed Drive
with Forward and Reverse. 10' Diameter Round Table with a Fixed Height
of 48". Pendant Control. (mw). Serial #NA. Good Condition
USED
RECONDITIONED TANK AND PIPE
TURNING ROLLS
1 ea T603002 Ransome PTR Pipe Support Stand. 1,000 lb Weight
Capacity. 2 to 36 Diameter Capacity. 8 Diameter x 2 Wide
Steel Wheels. 8 Height Adjustment from 24 to 32. Serial
#2918044 Good Condition
1 ea T612012 Pandjiris Model OS-15 Pipe Support Stand. 1,500 lb
Capacity. 2 to 24 Diameter Capacity. Manual Adjustable Height.
Serial #800-9138-1 Good Condition
2 ea T808007-008 Custom 2,000lb Idler Roll. 1.5 to 48
diameter capacity. 2,000 lb weight capacity. 10.5 diameter x
2.75 wide rubber wheels. Wheels manually adjust from 1.75 to 21
center to center by a threaded bolt. Good Condition
1 ea. T808009-010 Custom 2,000 lb Idler Roll. 1.5: to 60
diameter capacity. 2,000 lb weight capacity. 10.5 diameter x
2.75 wide rubber wheels. Wheel settings of 11 and 26 center
to center. Good Condition
1 ea T405001 Radian 3,000 lb Turning Rolls. Drive Roll with
Idler. 3,000 lb Total Weight Capacity. 16" Diameter x 4"
Wide Rubber Tires. Overload Discs. Constant Speed Friction Drive
Rotation. 4" Minimum to 36" Maximum Diameter Capacity.
230/460 Volt. Electrical Re-Conditioned - No Clean Up or Paint Good
Condition
1 ea T405002 Radian 3,000 lb Turning Rolls. Same As Above.
Electrical Re-Conditioned - No Clean Up or Paint Good Condition
1 ea T701005 Pandjiris Piper 3 Turning Rolls. 4,000 lb load
capacity, 3-1/2" to 40" diameter capacity. Variable speed
from 2.0 to 60 IPM. Drive and idler. 2-1/2" wide X 12"
diameter steel wheels on both the drive and idler. Pendant Control.
Serial #N/A Good Condition
1 ea T505006 Pandjiris Piper 3 Turning Rolls. 4,000 lb Load
Capacity, 3-1/2" to 40" Diameter Capacity. Variable Speed
from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12"
Diameter Rubber Wheels. Pendant Control. Serial #N/A Good Condition
1 ea T505007 Pandjiris Piper 3 Turning Rolls. 4,000 lb Load
Capacity, 3-1/2" to 40" Diameter Capacity. Variable Speed
from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12"
Diameter Rubber Wheels. Pendant Control. Serial #N/A Good Condition
1 ea T505008 Pandjiris Piper 3 Turning Rolls. 4,000 lb Load
Capacity, 3-1/2" to 40" Diameter Capacity. Variable Speed
from 2.0 to 60 IPM. Drive and Idler. 2-1/2" Wide X 12"
Diameter Rubber Wheels. Pendant Control. Serial #N/A Good Condition
4 ea T808003-006 Pandjiris Piper 3 2,000 lb Idler. 3.5 to
40 diameter capacity. 2,000 lb weight capacity. 12 diameter x
2.5 wide rubber wheels. Good Condition
1ea T100539 Riley 2 Ton Steel Wheel Idler Roll. 4,000 lb weight
capacity. 3 to 72 diameter capacity. 8 diameter x 2.25
wide steel wheels. Good Condition
1ea T100540 Riley 2 Ton Steel Wheel Idler Roll. 4,000 lb weight
capacity. 3 to 72 diameter capacity. 8 diameter x 2.25
wide steel wheels. Good Condition
1 set T605003 Worthington Ranger 3 Pipe Turning Rolls.
4,000 lb Capacity. 3.5 to 40 Diameter Capacity. Travel Speed
from .9 to 37.7 IPM. 3 Wide x 12 Diameter Rubber Wheels. Drive
& Idler. Pendant Control. 120 Volt. Serial #N/A Good Condition
1 ea T976004 Worthington Type A, 4000 lbs Driver Only. 15 dia.
X 3 Wide Rubber Faced Rolls, Variable Speed, 12,000 lbs Turning
Capacity. Good Condition
1 set T708014 Weldwire Model WWRD-2 4,000 lb Turning Rolls.
4,000 lb capacity for 1 drive and 1 idler. 3.5 to 40 diameter
capacity. 12 diameter x 3 wide rubber wheels. Pendant control.
120 volt. Serial #9439/9471 Good Condition
1 ea T100536 Aronson Model WSU-5 5,000 lb Steel Wheel Unit Frame
Turning Roll. 5,000 lb weight capacity. 148 bed length. 3 to
24 diameter capacity. Variable speed from 2 to 50 IPM. 12
diameter x 4 wide steel wheels. Pendant control.230 or 460 volt.
Serial #7341 Good Condition
1 ea T711010 Aronson WRI-5 5,000 lb Idler Roll. 5,000 lb weight
capacity. 6 to 12 diameter capacity. Idler Only !! Serial #n/a
Good Condition
1 ea T711011 Aronson WRI-5 5,000 lb Idler Roll. 5,000 lb weight
capacity. 6 to 12 diameter capacity. Idler Only !! Serial #n/a
Good Condition
1 ea T810023 Aronson WRI-5 5,000 lb Idler. 6 to 6 diameter
capacity. 12 diameter x 4.75 wide rubber wheels with overload
discs. Serial #9304 Good Condition
1 ea T810028 Cayuga 5,000 lb Power Elevation Unit Frame Roll.
5,000 lb weight capacity. 24 minimum length capacity. 30 to
72 diameter capacity. Variable speed travel. Powerd elevation from
36 to 48 to the top of the wheels. 12 diameter x 3 wide
rubber wheels. 230 or 460 volt. Serial #28A86 Good Condition
1 ea T100909 Cecil Peck 5,000 lb Unit Frame Turning Rolls with
Hold Down Device. 5,000 lb weight capacity, 8 to 42 diameter
capacity. Variable speed rotation. 5 wide x 9 diameter rubber
wheels, 2 wheels per shaft. 1 shaft is powered, the other is an idler.
40.5 high to the top of the wheels. Custom built for the welding of
pipe tees and elbows. 115 volt. On/Off foot pedal. Serial #
n/a Good Condition
1 ea T405003 Radian 5,000 lb Turning Rolls. Drive Roll with
Idler. 5,000 lb Total Weight Capacity. 16" Diameter x 1"
Wide Steel Wheels. Overload Discs. Constant Speed Chain Drive
Rotation. 4" Minimum to 36" Maximum Diameter Capacity.
230/460 Volt. Electrical Re-Conditioned - No Clean Up or Paint Good
Condition
1 ea T409004 Ransome/Worthington AIRR Idler Roll. 5,000 lb
Weight Capacity. 5 to 12 Diameter Capacity. 2-1/2 Wide x
16 Diameter Rubber Wheels Good Condition
1 set T10805 Teledyne-Readco TRR-50, 5000 lb Steel Wheel Turning
Rolls. Variable Speed ½ HP, 115 volt, Pendant Control of 2.5 to 75
IPM. 9 diameter x 4 wide Steel Wheels. For diameters from 3
to 66. Now set in unitized frame. 1980 Ser. #S-84563. Good
Condition.
2 ea T204001 Aronson T1I 6,000 Idler Roll. 6,000 lb Capacity.
24" Diameter x 3" wide Rubber Wheels. 4' Minimum Capacity,
10' Maximum Diameter Capacity. Idler Only. Serial #6049 Good Condition
1 ea T405007 Radian 10,000 lb Turning Rolls. Drive Roll and
Idler. 10,000 lb Total Weight Capacity. 16" Diameter x 3.5"
Wide Rubber Wheels. Constant Speed Rotation. 4" Minimum to
144" Maximum Capacity. 230/460 Volt. Electrical Re-Conditioned -
No Clean Up or Paint Good Condition
1 ea T209003 Aronson Model WPS4WD101-18 4-Wheel Drive Unit Frame
Pipe Turning Roll. "1995" 10,000 lb Capacity. 18" Frame
Length. 24" to 54" Diameter Capacity. 15" Diameter x
2.5" Wide Steel Wheels. Variable Speed from 2.0 to 50 IPM.
Pendant Control. Used for Overlaying of Short Steel Mill Rolls. Serial
#9580 Good Condition
1 ea T810025 Aronson WRD-10C Drive Roll. 10,000 lb weight
capacity, 30,000 lb turning capacity. 12 to 6 diameter capacity.
Variable speed from 2 to 50 ipm. 20 diameter x 5 wide rubber
wheels with overload discs. Serial #72033 Good Condition
1 ea T508003 Worthington A 10,000 lb Turning Rolls. 10,000
lb Weight Capacity.5 to 72 Diameter Capacity. Variable Speed
Rotation from 6.1 to 61 IPM by a Sheave Drive. 16 Diameter x 3
Wide Rubber Wheels. On/Off Pendant. 230/460Volt. Drive and Idler.
Serial #N/A As-Is
1 ea T100703P Aronson Model T1D-6-12 12,000 lb TracTred Turning
Roll Set. 12,000 lb weight capacity per set. 6 to 12 diameter
capacity. Variable speed drive from 3 to 80 IPM with tractive pull for
9 ton concentric. Ύ hp. 20 pendant control. For steady, positive,
precision rotation of thin wall vessels. 230 or 460 volt. Serial
#79118 Reconditioned Price
1 ea T100704P Aronson Model T1D-6-12 12,000 lb TracTred Turning
Roll Set. 12,000 lb weight capacity per set. 6 to 12 diameter
capacity. Variable speed drive from 3 to 80 IPM with tractive pull for
9 ton concentric. Ύ hp. 20 pendant control. For steady, positive,
precision rotation of thin wall vessels. 230 or 460 volt. Serial #7999
Reconditioned Price
1 ea T209006 Aronson WRD-10/WRI-10 10 Ton Turning Rolls. 20,000
lb weight capacity. 6 to 13 diameter capacity. Variable speed
travel from 2 to 50 IPM. 12 diameter x 4 wide rubber wheels with
over load discs. Drive & Idler. Serial #63132 Good Condition
1 ea T906042 Aronson WRD-10/WRI-10 10 Ton Turning Rolls. 20,000
lb weight capacity. 6 to 13 diameter capacity. Variable speed
travel from 2 to 50 IPM. 12 diameter x 4 wide rubber wheels with
over load discs. Drive & Idler. 230 or 460 volt. Serial #72263
Good Condition
1 ea T100537 Riley 10 Ton Steel Wheel Idler Roll. 20,000 lb
weight capacity. 16 to 10 diameter capacity. 12.5 diameter x
9.5 wide steel wheels. Good Condition
1 ea T100545 Riley 10 Ton Steel Wheel Idler Roll. 20,000 lb
weight capacity. 16 to 10 diameter capacity. 12.5 diameter x
9.5 wide steel wheels. Good Condition
1 set TSP10802P Pandjiris MM-15T-SPL Rotation System for
Ultrasonic Testing. This is a U.T. Rotation System for Digitally
Indicated, Variable Speed, Turning of Cylindrical Parts under fluids
flow. The System uses the Missouri Mule 15 Ton Turning Roll
Configuration, Specially Manufactured for this type of Testing. The
Drive Wheels are 16 dia. Grooved, Hardened Steel which are can be
pivoted up and down for various workpiece diameters. The Idler Wheels
are 6 Grooved, Hardened Steel , and have 13 of Motorized Powered
Adjustable Height. There are Vertical Thrust Rolls on both
driver and idler to prevent unwanted walking. The Driver and
Idler separation is adjustable for lengths from 24 to 100 by a
long hand wheel screw. The whole system is in a fluid collection pan.
Ser. #673-862 Very Good Condition
1 set TSP10801P Pandjiris MM-30T-SPL Rotation System for
Ultrasonic Testing. This is a 1994 U.T. Rotation System for
Digitally Indicated, Variable Speed, Turning of Cylindrical Parts
under fluids flow. The System uses the Missouri Mule 30 Ton Turning
Roll Configuration, Specially Manufactured for this type of Testing.
The Drive Wheels are 20 dia. Grooved, Hardened Steel which are can
be pivoted up and down for various workpiece diameters. The Idler
Wheels are 6 Grooved, Hardened Steel , and have 14 of Motorized
Powered Adjustable Height. There are Vertical Thrust Rolls on
both driver and idler to prevent unwanted walking. The Driver
and Idler separation is adjustable for lengths from 30 to 120 by
a long hand wheel screw. The whole system is in a fluid collection pan
fitted with removable platform slat sections. Ser. #SO. 60-4604
1 ea T101003 Aronson Model WRD-17 15 Ton Turning Roll Set. Drive
and Idler.30,000 lb weight capacity. 6 to 13 diameter capacity.
Variable speed from 2 to 50 IPM. 12 diameter x 8 wide rubber
wheels with overload discs. Pendant control. 230 or 460 volt. Serial
#6127/6128 Good Condition
1 ea T100532P Ransome BPRR 15 30,000 lb Drive Roll Only. 15 Ton
set down weight capacity, 45 ton turning capacity. 8 to 8
diameter capacity. 7 wide x 20 diameter rubber wheels. Variable
speed from 1.5 to 59 IPM. 230 or 460 volt. Serial #352494 Good
Condition
1 ea T100533P Ransome BPRR 15 30,000 lb Drive Roll Only. 15 Ton
set down weight capacity, 45 ton turning capacity. 8 to 8
diameter capacity. 7 wide x 20 diameter rubber wheels. Variable
speed from 1.5 to 59 IPM. 230 or 460 volt. Serial #n/a Good Condition
1 ea T100534P Worthington BPRR 15 30,000 lb Drive Roll Only. 15
Ton set down weight capacity, 45 ton turning capacity. 8 to 10
diameter capacity. 7 wide x 20 diameter rubber wheels. Variable
speed from 1.5 to 59 IPM. 230 or 460 volt. Serial #n/a Good Condition
1 ea T901016 Ransome Model BIRR 15 Ton Idler Roll Only. 30,000
lb weight capacity. 7 to 14 diameter capacity. 7 x 20
diameter rubber wheels. Serial #n/a Good Condition
1 ea T704008 Aronson Model WRD-30 30,000 lb Drive Roll Only.
30,000 lb weight capacity. 90,000 lb turning capacity. 8 to 18
diameter capacity. Variable speed from 1.4 to 40 IPM. 20 diameter x
7 wide rubber wheels with overload discs. 240/460 volt. Serial #N/A
Reconditioned and Ready to Ship with new idler.
1 ea T808002 Ransom SA-15PR/SA-7.5IR Rustler 15 Ton
Turning Roll Set. Drive and Idler. Ransome Rustler rolls automatically
adjust to take any circular piece from 12 to 10 diameter. 30,000
lb weight capacity. 12 diameter x 3.5 wide rubber wheels.
Variable speed travel from 4.8 to 48 ipm. Pendant Control. 230 or 460
volt. Serial #7925369/8025370 Good Condition
1 ea T906041 Pandjiris Model MM30/15 Missouri Mule Turning
Rolls. Drive and Idler. 60,000 lb Weight Capacity. 12 to 16
Diameter Capacity. Variable Speed from 5.3 to 53 IPM. 20 Diameter x
10 Wide Rubber Wheels. Pendant Control. 230 or 460 Volt. Serial
#800-3499-1 Good Condition
1 ea T911001P Pandjiris 30 Ton Steel Wheel Turning Rolls. 60,000
lb load capacity. Variable speed Drive. 24 to 16 diameter
capacity. Drive roll has 20 diameter x 10 wide steel wheels,
Idler roll has 20 diameter x 7 wide steel wheels. 230 or 460
volt. Serial # na Good Condition
1 ea T911002P Pandjiris 30 Ton Steel Wheel Turning Rolls. 60,000
lb load capacity. Variable speed Drive. 24 to 16 diameter
capacity. 20 diameter x 7 wide steel wheels on both drive and
idler. 230 or 460 volt. Serial # na Good Condition
1 ea T100910 Ransome Model BPRR/BIRR 30 Ton Turning Roll Set.
Drive and Idler. 60,000 lb weight capacity (add an additional idler
for a total capacity of 90,000 lb). 7 to 20 diameter capacity.
7 wide x 20 diameter rubber wheels. Variable speed rotation from
1.45 to 58 ipm. Pendant control. 230 or 460 volt. Serial #n/a Good
Condition
1 ea T901014 Ransome Model BPRR/BIRR 30 Ton Turning Roll Set.
60,000 lb weight capacity (add an additional idler for a total
capacity of 90,000 lb). 7 to 20 diameter capacity. 7 wide x
20 diameter rubber wheels. Variable speed rotation from 1.45 to 58
ipm. Pendant control. 230 or 460 volt. Serial #665832/3626430 Good
Condition
1 ea T901018 Ransome Model CPRR 30 Ton Drive Roll Only. 60,000
lb weight capacity, 180,000 lb turning capacity. 7 to 20
diameter capacity. 14 wide x 20 diameter rubber wheels. Variable
speed rotation from 1.45 to 58 ipm. Pendant control. 230 or 460 volt.
Serial #3725801 Good Condition
1 ea T901019 Ransome Model CPRR 30 Ton Drive Roll Only. 60,000
lb weight capacity, 180,000 lb turning capacity. 7 to 20
diameter capacity. 14 wide x 20 diameter rubber wheels. Variable
speed rotation from 1.45 to 58 ipm. Pendant control. 230 or 460 volt.
Serial #1305 Good Condition
1 ea T901021 Pandjiris Unit Frame 34 Ton Turning Rolls on
Variable Speed Travel Car. 68,000 lb turning capacity. 7 to 14
diameter capacity with a fixed axel center of 72. Variable speed
rotation. 5 sets of 5 wide x 20 diameter rubber wheels spaced
over the 30 length of a variable speed travel car that runs on
69 gauge rail track. Pendant control. Serial # 60-4595 Good
Condition
1 ea T901022 Pandjiris Unit Frame 34 Ton Turning Rolls on
Variable Speed Travel Car. 68,000 lb turning capacity. 7 to 14
diameter capacity with a fixed axel center of 72. Variable speed
rotation. 5 sets of 5 wide x 20 diameter rubber wheels spaced
30 over the length of a variable speed travel car that runs on
69 gauge rail track. Pendant control. Serial #n/a Good Condition
1 ea T810030 Aronson WND60CS-86 Turbine Turning Roll Set. 60 ton
capacity. 8 to 6 diameter capacity. Constant speed rotation.
27 diameter x 5.75 wide neoprene wheels. Serial #7386 Good
Condition
1 ea T901011 Aronson Model WRI-60 30 Ton Idler Only. 60,000 lb
weight capacity. 8 to 18 diameter capacity. 12 wide x 20
diameter rubber wheels. Serial #n/a Good Condition
1 ea T901012 Aronson Model WRI-60 30 Ton Idler Only. 60,000 lb
weight capacity. 8 to 18 diameter capacity. 12 wide x 20
diameter rubber wheels. Serial #n/a Good Condition
1 ea T110101C Ransome Model DIRR 45 Ton Close Coupled Idler
Roll. 90,000 lb capacity. 22 diameter x 20 wide rubber tires.
10 to 20 diameter capacity. Serial #407649 Ready to be put into
Service
1 ea T901003 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll
Set. 180,000 lb capacity. 4 to 10 diameter capacity. 16 wide
x 42 diameter foam filled rubber truck tires. Pendant Control. 460
volt. Serial #3931611/4031261 Good Condition
1 ea T901004 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll
Set. 180,000 lb capacity. 4 to 10 diameter capacity. 16 wide
x 42 diameter foam filled rubber truck tires. Pendant Control. 460
volt. Serial #3931612/4031615 Good Condition
1 ea T901005 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll
Set. 180,000 lb capacity. 4 to 10 diameter capacity. 16 wide
x 42 diameter foam filled rubber truck tires. Pendant Control. 460
volt. Serial #3931253/4032376 Good Condition
1 ea T901006 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll
Set. 180,000 lb capacity. 4 to 10 diameter capacity. 16 wide
x 42 diameter foam filled rubber truck tires. Pendant Control. 460
volt. Serial #na/4033765 Good Condition
1 ea T901007 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll
Set. 180,000 lb capacity. 4 to 10 diameter capacity. 16 wide
x 42 diameter foam filled rubber truck tires. Pendant Control. 460
volt. Serial #na/na Good Condition
1 ea T901008 Ransome Model DPRRPT/DIRRPT 90 Ton Turning Roll
Set. 180,000 lb capacity. 4 to 10 diameter capacity. 16 wide
x 42 diameter foam filled rubber truck tires. Pendant Control. 460
volt. Serial #3933763/4033766 Good Condition
1 ea T605019 Teledyne-Readco 150 Ton Turbine Rolls. 150 ton
weight capacity. 4 to 48 diameter capacity. Variable speed drive
from 0 to 48 IPM. 23-1/2 diameter x 16 wide rubber wheels. Drive
and idler. Serial #105839/105840 Reconditioned and Ready to Ship !
1 set T008002P Aronson 200 Ton Twin Driver Turning Rolls.
Model WSD-200-S2G. 3 to 10 diameter capacity. Twin Driver
Turning Rolls use one Driven Wheel on each Roll Stand. Also one of
these driven wheels has Two Final Gear Drive Worm Gears on each side
of the axle, thus the two pinions work in opposite directions to
Eliminate Backlash. This Design was developed by Aronson for Babcock
& Wilcox so the turning rolls could be used under Vertical Boring
Mills. Ser.# 667 Good Condition
USED
WELDING MANIPULATORS
1 ea M100907P P & A 200 lb Parts Manipulator. 200 lb
concentric load capacity. Powered arm elevation from 1 to 5. Arm
manually rotates 360 degrees with an air lock. Head mounted on a 4
long arm rotates 360 degrees with an air lock. Mounting base has a 360
degree manual rotation with an air lock. 460 volt. As-Is Condition !!
8 ea M610004 Positech Model G Simple Air Manipulator.
Positech Model G SAM Parts Manipulator uses Pneumatic Power to Provide
Quick Response and Superior Maneuverability with Loads up to 370 lbs.
Vertical Lift from 44.7 to 87.3. Reach from 66 to 126. 360
Degree Full Rotation. Includes Portable Base with Fork Truck Lifting
Slots. Good Condition
1 ea M806001 Roller & Assoc. Head Director Manipulator on
Manual Travel Car. Adjustable height from 49 to 112 by a manual
hand pump hydraulic cylinder. Reach 71 when at 49, 43 reach
when at 112 and 74 reach with the arm level. 360 degree manual
mast rotation. 4 manual cross slides mounted on the end of the boom
arm. All mounted on a manual travel car. Serial #n/a Good Condition
1 ea M409001 Porta Tools / Lincoln Model H-600 26 x 48
Manipulator. Constant Speed Power Reach from 24 to 50, Screw
Driven Constant Power Elevation from 12 to 60. Lincoln DC-600
Power Supply and a NA-5 Submerged Arc Control and Head, Lincoln Manual
Horizontal and Vertical Adjusters. All Mounted on a Variable Speed
Travel Car with 40 of Track. Serial #W7702-0270 Good Condition
1 ea M606017 Ransome Model 44 4 x 4 Manipulator / Travel
Car. 4 Constant Speed Powered Lift from 25 to 73. Manual
Reach from 9 to 57 from the Center of Mast Rotation. Manual King
Pin Base. Manual Travel Car. 115 Volt. Serial #0526806 Good Condition
1 ea M901023P Pandjiris 4 x 37 Telescoping Boom
Manipulator. 191 overall height. 48 constant speed powered
elevation from 57-3/4 to 105-3/4 to the centerline of the arm. 3
to 116 IPM variable speed powered reach telescoping boom with a total
reach of 376. Fixed non swivel bolt down base. 460 volt. Serial
#60-4596 Good Condition
1 ea M110103 Ransome Model 1212 5 x 8 Travel Car
Manipulator. 750 lb capacity either or both ends. 5 constant speed
powered lift from 62 to 122 distince to the floor when mounted
on the travel car. 4.1 to 165 ipm variable speed reach from 30.5 to
122.5 from the center of the mast. Mounted on a variable speed rack
and pinion driven travel car that runs on 20 of 33 gauge track.
230 or 460 volt. Serial #623657 Ready to be reconditioned to fit your
needs!
1 ea M1011009 Custom 6 x 4 Torch Manipulator. 6
constant speed powered elevation from 25 to 97 from the floor to
the bottom of the arm. 48 variable speed reach. 12 vertical
slide for fine height adjustment. 6 powered cross seam adjuster.
Manual rotary slide to level the reach arm. Remote pendant station for
all controls. 230 or 460 volt. Ready to be reconditioned to fit your
needs
1 ea M911003 Aronson G6VRA6CL-PK 6 x 6 Locust I
Manipulator. 400 lb weight capacity either or both ends. 6 constant
speed powered lift from 29.5 to 101.5.13 to 85 variable
speed reach from 3.3 to 100 IPM. 360 degree manual mast rotation.
Portable X frame base. Currently equipped with the following:
180 degree manual X and Y axis swivels on the welding head, Jetline
ALC-101V-6T arc length control, Jetline CWF-10A cold wire feeder,
Cyclomatic 80A magnetic arc oscillator, horizontal powered cross
slide, 500 amp water cooled machine tig torch and a Miller Maxstar
300DX Tigrunner Package.115 volt. Serial #80430 Very Good Condition
1 ea M100404 Aronson Model G6VRA6CL-PK 6 x 6 Manipulator.
400 lb load capacity either or both ends. 6 constant speed powered
elevation from 29.5 to 101.5. 3.3 to 100 IPM variable speed
reach from 13 to 85 from the center of the mast rotation. 360
degree manual mast rotation on a portable X frame base. 230 or
460 volt. Serial #97558 Good Condition
1 ea M100918 Aronson Model G6VRA6CL-PK 6 x 6 Manipulator.
400 lb load capacity either or both ends. 6 constant speed powered
elevation from 29.5 to 101.5. 3.3 to 100 IPM variable speed
reach from 13 to 85 from the center of the mast rotation. 360
degree manual mast rotation on a portable X frame base. Pendant
control for all functions. 115 volt. Serial #74165 Good Condition
1 ea M903004 Preston-Eastin MA-66MD 6 x 6 Manipulator. 150
lb weight capacity either or both ends. 6 powered lift from
24-1/4 to 96-1/4. 6 4.0 to 100 IPM variable speed powered
reach from 18-1/2 to 90-1/2. 360 degree manual mast rotation.
Bolt down base. 115 volt. Serial #MB66MD-27 Good Condition
1 ea M908003P Ransome Model 1212 6 x 8 Manipulator and
Travel Car with Track. 6 constant speed lift from 57.75 to
105.75. 1 to 62 IPM variable speed reach from 27 to 122. 360
degree manual mast rotation. 5 to 200 IPM Variable speed travel car
that runs on 70 (2 sections 20, 3 sections 10) of 33 gauge
track. Currently equipped with 4 ea Lincoln DC-600 power supplies, 2
ea Lincoln NA-3N controls with feed heads, vertical and horizontal
adjusters for each weld head all mounted on manual spotting cars
mounted on the manipulator boom and an Invincible flux recovery
system. 460 volt. Serial #629592 Good Condition
1 ea M904018 Ransome Model XXHD 7 x 15 Travel Car
Manipulator. 7 powered elevation from 77 to 164 to the bottom
of the boom. 2.7 to 108 IPM variable speed reach from 64 to 244
from the center of the mast rotation. 360 degree power mast rotation.
2,000 lb load capacity either or both ends. Mounted on a variable
speed travel car that runs on 84 gauge rail track. Track NOT
Included. 460 volt. Serial #909286 Reconditioned Price
1 ea M309004 Mark "V" 8' x 5' Manipulator and Travel
Car. 8' Constant Speed Power Elevation from 32" to 128". 5'
Variable Speed Power Reach from 15" to 75". Manual Mast
Rotation. With 6" Linde Powered Horizontal and Vertical Cross
Slides and a Manual Rotary Slide. All Mounted on a Manual Travel Car
that Runs on Inverted Angle Iron Track (Track Not Included). Currently
Equipped with a L-Tec 650 CC/CV Power Supply, GMA Feed Head and all
Cables. Remote Control Console for all functions Including Welding
Process. Serial #6620-34-31 Good Condition
1 ea M101002 Pandjiris Model 808 Piper 8 x 8
Manipulator. 250 lb weight capacity on either end. Constant speed rack
and pinion driven lift from 31 to 127 to the bottom of the boom.
Variable speed rack and pinion driven reach from 24 to 120 from
the center of the boom. 360 degree manual mast rotation. Mounted on a
48 square mobile base. 230 or 460 volt. Serial #25-2130 Good
Condition
1 ea M909007P Pandjiris Model 8 X 8 Manipulator. 300 lb load
capacity either end, 500 lb total weight capacity. 8 constant speed
powered lift from 21 to 117. 3 to 117 ipm variable speed power
reach from 20-5/8 to 112. 360 degree manual king pin X
frame base. Currently equipped with a Jetline 9200 weld oscillator, a
Cyclomatic 6 x 6 seam tracker, a 6 manual cross slide and a
rotary cross slide. 115 volt. Serial #11998X02-2 Very Good Condition
1 ea M906039 Aronson G8VRA8CL-PK 8 x 8 Locust I
Manipulator. 8 variable speed reach from 13 to 109 from the
center of the mast rotational axis. 8 constant speed lift from
29.5 to 125. 300 lb load capacity either or both ends. 360
degree manual mast rotation. Portable king pin base. 115 volt. Serial
86528 Reconditioned and Ready to Ship
1 ea. M404001 Precision 9 x 9 x 27-1/2 Heavy Duty
Manipulator/Travel Car System. This system was manufactured for the
Robotics Industry for precision welding on military vehicles. Heavy
Duty Mast has 9 ft. of constant speed of precision screw driven lift
starting at approx. 36 from the floor to 144 high under the
boom. The mast has manual rotation with lock. Boom has 9 ft. of
Dual Pinion variable speed gear drive and rolls on Thompson
Round way roller system. Weight capacity approx. 750 lb. Travel car is
5 x 5 x 19 High and Variable Speed Rack & Pinion Drive on
33 ft. of Thompson Round way Precision Track. All three (3)-axis paths
are accordion booted. This system is now Servo driven. We will change
to Pendant AC-Inverter or D.C. Drives. Very Good Condition
1 ea M803002 Ransome Model 1212 9 x 11 Manipulator. 9
constant speed power lift from 29-1/2" to 137-1/2". 11
variable speed reach from 35" to 171" from the center of the
mast rotation. 750 load capacity either or both ends. 360 degree
manual mast rotation. Bolt down base. 230 or 460 volt. Serial #6211821
Ready to be reconditioned to fit your needs
1 ea M103004 Aronson Model 2G10VRA10CL-SK 10 x 10
Manipulator. 400 lb weight capacity either or both ends. 10
constant speed powered lift from 37.25 to 157.25. 10 Variable
speed reach from 13 to 133 from the center of the mast. Manual
mast rotation. Mounted on a manual travel car with 10 inverted
angle iron track. Currently equipped with a Lincoln DC-600 power
supply, a Lincoln NA-5 head and control, cables and vertical and
horizontal adjusters. 230 Volt. Serial #733. As Equipped!! - Good
Condition
1 ea M110306 Ransome Model 1212 12 x 12 Manipulator. 12
Constant Speed Power Lift at 36 IPM from 39-1/2 to 183-1/2 to
the center of the Boom. 12 Variable Speed Power Reach of 3.7 to 150
IPM from 30-1/2 to 174-1/2 from the Center of the Mast. 750 lb
Weight Capacity Either or Both Ends. 360 Degree Manual Rotation on a
Bolt Down Base. Pendant Control. 230 or 460 volt. Serial #622604
Reconditioned and ready to ship
1 ea M807004 Ransome Model 1212 12 x 12 Travel Car
Manipulator. 750 lb weight capacity either or both ends. 38 ipm
constant speed power lift from 62.25 to 206.25. 3.35 to 134 ipm
variable speed reach from 39.5 to 183.5. 360 degree manual mast
rotation. Mounted on a 33 gauge rack and pinion travel car with a
speed range from 5 to 200 ipm. Travel car includes 30 of track.
Pendant control for all functions. Welding equipment NOT included. 460
volt. Serial #692597 Good Condition
1 ea M100530P Webb MB1212 12 x 12 Travel Car Manipulator.
12 constant speed screw driven powered lift from 51 to 195.
Variable speed rack & pinion driven reach from 32 to 176.
360 degree manual mast rotation. Mounted on a variable speed travel
car that runs on 56-1/2 gauge track (track NOT included). 230 or
460 volt. Serial #7042 Good Condition
1 ea M710002 Ransome Model XXHD 13.5 x 18 Travel Car
Manipulator. 13.5 powered elevation from 77-1/2 to 239-1/2
to the bottom of the boom. 2.7 to 108 IPM variable speed reach from
55 to 271 from the center of the mast rotation. 360 degree power
mast rotation. 2,000 lb load capacity either or both ends. Mounted on
a variable speed travel car that runs on 84 gauge rail track. Track
NOT Included. 460 volt. Serial #639089
USED
WELD SEAMERS
1 ea S209001 Jetline 6" Custom Weld Seamer. 1997 Variable
Speed Jetline Carriage on a Jetline Model TKS-24 Side Beam with
24" Travel. Currently Has a Total Clamping Length of 6" (Can
be Increased with a New Clamping Fixture to a Length of 24" to
Match Side Beam). 3" Vertical and Horizontal Cross Slides and a
Rotary Slide. No Welding Equipment!! Serial #970295 Good Condition
1 ea S209003 Jetline 6" Custom Weld Seamer. 1997 Variable
Speed Jetline Carriage on a Jetline Model TKS-24 Side Beam with
24" Travel. Currently Has a Total Clamping Length of 6" (Can
be Increased with a New Clamping Fixture to a Length of 24" to
Match Side Beam). 3" Vertical and Horizontal Cross Slides and a
Rotary Slide. Complete with Plasmfix 50S Plasma Welding Power Supply
and Miller Water Circulator. Serial #970299 Good Condition
1 ea S604011 1990Mills Machine 11 Longitudinal Plasma
Seam Welder. 11 Overall Welding / Clamping Length Capacity.
3-1/2 to 5-1/2 Diameter Capacity ( Can be Increased with a Riser
). Variable Speed Screw Driven Carriage. 3 Pneumatic Torch Lifter.
Gas Purge Back p Bar, Water Cooled Mandrel, Dual Water Circulators.
Plasma Welding Equipment Includes a Thermal Dynamics WC100B Welding
Console, Airco Heliwelder Power Supply and Multi Slope 2 Sequence
Control, Model 3A Plasma Torch and a Cyclomatic 80A Magnetic Welds
Oscillator. Serial # N/A Good Condition
1 ea S502007 Jetline 12 Coil End Joining Seam Welder. This
seam welders primary use is to join together strips fed from coils.
The Jetline Seamer Clanping/Welding bed is 12-1/2 long. Has a
Variable Speed Carraige with #9026 Control and two manual cross slides
on the torch holder. The one piece hold down clamps are air actuated
with individual air valves. There are 2 ea 8 dia. primary strip
guide rolls and 2 ea 3 final guide rolls. The Welding Package is a
Miller 50A Precision Tig Welding Power Supply and and Air-Cooled Tig
Torch for the fusion only weld. The whole system is mounted on a self
contained portable base. Dimensions of the whole system are 78 lg.
x 40 w x 58 h. Jetline Ser. 84166. Very Good Condition
1 ea S412001 Cecil Peck Dual Position Outside Corner Seam
Welder. This Machine was Used to Tig Weld the Outside Corners of
Aluminum, Steel and Stainless Electric Panel Boxes. The Dual Operator
Positions were Used for Weld Lengths up to 17 Long. The Air
Clamping Device and Copper Mandrel Plates Could be Increased (Within
Reason) for Longer Welds. The Torch Carriers are Heavy Duty Variable
Speed Devices that are ½ H.P. Dc Motors & Drives. Reconditioned
with 2 Cold Wire Feeders or Converted to Mig Welding Including Power
Sources
1 ea S505002 Pandjiris Model 24E-3-5-30 24 Weld Seamer. 30
Total Clamping / Welding Length. 3-1/4 Minimum Parts Diameter,
32 Maximum Parts Diameter ( Can be Increased with a Riser ). Rack
and Pinion Drive Variable Speed Carriage. Water Cooled Mandrel. Plate
Alignment Devices. Jetline Model 9029 Cold Wire Feeder and Model 9033
Pulse Control. Power Supply NOT Included. Serial #400-9364. Good
Condition
1 ea S10302 Jetline LWS-24Z, High Production , Automatic
Seamwelder. This 1996 Automatic Plasma Welding Seamwelder is a High
Production Machine that Features: Automatic Clamping & Alignment
for Cylinders up to 24 long , 18 to 25 in diameter, and .020
to .187 Thickness, Microprocessor Control, Thermal Arc Ultima 150
Plasma Welding System, Safety Palm Buttons & Guards, and More!
Minimum Operator Skill Required, This machine was used for a short run
product. Very Low Hours, Excellent Condition
1 ea S100801 Jetline Model LWS-24 24 Weld Seamer. 30 total
welding/clamping length capacity. Currently equipped with a mandrel
for flat sheet seaming (can be converted to a standard mandrel with a
2.625 minimum part diameter and a maximum diameter of 32, with
mandrel latch for an additional charge). A riser can be added for
larger diameter capacity. Variable speed rack and pinion carriage that
runs on precision round ways. Welding Equipment NOT included. Serial
#n/a Good Condition With Current Mandrel
1 ea S100802 Jetline Model LWS-24 24 Weld Seamer. 30 total
welding/clamping length capacity. Currently equipped with a mandrel
for flat sheet seaming (can be converted to a standard mandrel with a
2.625 minimum part diameter and a maximum diameter of 32, with
mandrel latch for an additional charge). A riser can be added for
larger diameter capacity. Variable speed rack and pinion carriage that
runs on precision round ways. Welding Equipment NOT included. Serial
#920227 Good Condition With Current Mandrel With NEW Mandrel and
Mandrel Latch
1 ea S100803 Jetline Model LWS-24 24 Weld Seamer. 30 total
welding/clamping length capacity. Currently equipped with a mandrel
for flat sheet seaming (can be converted to a standard mandrel with a
2.625 minimum part diameter and a maximum diameter of 32, with
mandrel latch for an additional charge). A riser can be added for
larger diameter capacity. Variable speed rack and pinion carriage that
runs on precision round ways. Welding Equipment NOT included. Serial
#n/a Good Condition With NEW Mandrel and Mandrel Latch
1 ea S901029 Jetline Model LWS-36Z Longitudinal Seam Welder.
42 total welding / clamping length capacity. 2.5 minimum part
diameter. 32 maximum part diameter (can be increased with a riser).
.020 to 3/8 thickness capacity. Variable speed rack & pinion
driven carriage with a 9627 carriage control. Plate alignment devices.
Water cooled mandrel. 6 x 3.5 manual cross slides. Air torch
lifter. Welding Equipment NOT Included !! Serial #060110 New in
2006!! Excellent Condition!!
1 ea S906032 Jetline LWS-36 3 Weld Seamer. 42 total
welding/clamping length capacity. 3.5 minimum part diameter. 32
maximum part diameter capacity (can be increased with a riser). Model
OM-48 rack and pinion driven carriage. Water cooled mandrel. 2
vertical and horizontal slides. Welding equipment NOT included. 115
volt. Serial #n/a Good Condition
1 ea S100709 Airline/Jetline Model LW10306 36 Weld Seamer.
42 total welding/clamping length capacity. 3 minimum part
diameter capacity. 32 maximum part diameter capacity. Variable
speed Model OM-48 rack and pinion carriage that runs on an 8
extended length side beam. Gas purge back-up bar. Welding equipment
NOT included. Serial #1105 Good Condition
1 ea S612013 Pandjiris Model 36ES-30 36 Seam Welder. 42
Welding/Clamping Length Capacity. 3 Minimum Part Diameter. 30
Maximum Part Diameter ( Can be Increased with a Riser ). Variable
Speed Rack and Pinion Driven Carriage. Water Cooled Mandrel. 6
Manual Cross Slides. Serial #400-8078 Good Condition
1 ea S100906 Airline/Jetline 48 Longitudinal Seam Welder.
48 total welding/clamping length capacity. 3.5 minimum part
diameter. 32 maximum part diameter capacity (can be increased with
a riser). Variable speed rack and pinion driven carriage. Serial #n/a
Good Condition
1 ea S101202 Airline/Jetline Model FAL10308 48 Seam Welder.
48 maximum welding/clamping length capacity. 5.5 minimum part
diameter capacity. 32 maximum part diameter capacity (can be
increased with a riser). Variable speed rack & pinion driven
carriage. Cyclomatic AVC-3 arc voltage control. 4 vertical and
horizontal slides. Rotary slide. Gas purge back-up bar. Continuous
copper fingers. Serial #1322. Welding power supply NOT included !!
Reconditioned with existing equipment !! Reconditioned Seamer
Bed Only No Welding Equipment !
1 ea S608005 Hamilton Custom 48 Weld Seamer. 52
Welding/Clamping Length. 6 Minimum Part Diameter. 58 Maximum
Part Diameter Capacity. Air Clamping. Side Beam, Carriage and Welding
Equipment NOT Included. AS IS Condition
1 ea S100202 Pandjiris Model 48E-36 48 Seam Welder. 54
total welding/clamping length. 4 minimum part diameter. 36
maximum part diameter (can be increased with a riser). Rack and pinion
driven variable speed carriage. Gas purge back-up bar. Water cooled
mandrel. Air torch lifter. 2 vertical and horizontal adjusters.
Serial #400-8596 Good Condition
1 ea S708003 Berkeley-Davis Model S-2 5 Weld Seamer. 60
total welding/clamping length capacity. 12 minimum part diameter.
72 maximum diameter. Rack & pinion driven variable speed
carriage. Water cooled mandrel. 6 manual vertical and horizontal
slides. Welding equipment NOT included. Serial #672548 Good Condition
1 ea S512003 Webb Model J-68 5 Seam Welder. 68 total
Welding/Clamping Length. 6 Diameter Minimum Capacity. 32
Diameter Maximum Capacity. .020 to .135 Thickness Capacity. Water
Cooled Mandrel. Includes a Lincoln TC-3 Variable Speed Travel
Carriage, Lincoln NA-5 or NA-3 Control and Head, Lincoln Vertical and
Horizontal Adjusters and Lincoln DC-600 Power Supply. 4 Individual
Copper Fingers, Copper Back-up Bar. Serial #59115 Good Condition
1 ea S110104P Ameco 72 Seam Welder. 72 total
welding/clamping length capacity. 10 minimum part diameter
capacity. 40 maximum part diameter capacity. Linde OM-48 rack and
pinion driven carriage. Currently equipped with a Miller Deltaweld
451, Automatic 1A and 4-roll wire feed head. Serial #5640
Reconditioned As Equipped or Reconditioned Bed Only !
1 ea S100708 Airline/Jetline Model FAL10312P 72 Weld Seamer.
78 total welding/clamping length. 5 minimum part diameter
capacity. 32 maximum part diameter capacity (can be increased with
a riser). Variable speed model OM-48 rack and pinion driven carriage.
Water cooler mandrel. Gas purge back-up bar. Welding equipment NOT
included. Serial #1316. Good Condition
1 ea S110201P Pandjiris Model 72-F6-32 72 Seam Welder. 78
total welding/clamping length capacity. 6 minimum part diameter
capacity. 32 maximum part diameter capacity ( we can include a
24 riser for a diameter capacity of 56 if needed). Pandjiris
rack and pinion driven carriage. 6 manual vertical and horizontal
adjusters. Plate alignment bar. Cable tray. Currently equipped with a
Miller Deltaweld 451, S-54A Feeder and automatic mig gun. Serial
#41-1210 As-Is Price. Reconditioned As Equipped or Reconditioned Bed
Only
1 ea S609006 Pandjiris Model 72-ES-52 72 Seamer. 74 Total
Welding / Clamping Length. 4 Minimum Part Diameter. 48 Maximum
Part Diameter. Equipped with a Variable Speed Model OM-48 Carriage,
Vertical and Horizontal Adjusters. Air Actuated Torch Lifter. Spatter
Shields. Water Cooled Mandrel. Serial #25-1969. Welding Equipment NOT
Included !! Very Good Condition
1 ea S611019P Pandjiris Model #572 72 Weld Seamer. 78
Welding/Clamping Length Capacity. 5 Minimum Part Diameter. 32
Maximum Part Diameter ( Can be Increased with a Riser ). Variable
Speed Rack and Pinion Driven Carriage. Serial #25-1046 Good Condition
1 ea S505001 Pandjiris Model 72-ES-52 72 Seamer. 78 Total
Welding / Clamping Length. 6 Minimum Part Diameter. 52 Maximum
Part Diameter (Currently has an 18 High Riser that can be Removed).
Equipped with a Variable Speed Carriage, Air Clamping Mandrel, Cable
Track and 4 Powered Vertical and Horizontal Cross Slides. Welding
Equipment NOT Included !! Serial # N/A Good Condition
1 ea S912007 Pandjiris Model 72-F6-36 72 Seamer. 78
clamping/welding length capacity. 6 minimum part diameter capacity.
32 maximum part diameter ( can be increased with a riser ). Rack
and pinion driven variable speed carriage. Cable tray. Water cooled
mandrel. 6 manual cross slides. Welding equipment NOT included.
Serial #8-4095-1 Good Condition
1 ea S110301P Pandjiris Model 72-F6-42 72 Seam Welder. 78
total welding/clamping length capacity. 6 minimum part diameter
capacity. 34 maximum part diameter capacity (can be increased with
a riser ). Pandjiris rack and pinion driven carriage. 4 manual
vertical and 2 horizontal adjusters. Plate alignment bar. Cable
tray. Currently equipped with a Miller Invision 456P, S-64M Feeder and
automatic mig gun. Serial #12133E00 As-Is Price or Reconditioned As
Equipped
1 ea S912008 Webb Model J-80 80 Welding Seamer. 80
clamping/welding length capacity. 6 minimum part diameter capacity.
32 maximum part diameter capacity. Rack and pinion driven variable
speed carriage. Cable tray. Water cooled back up bar. 6 manual
cross slides. Welding equipment NOT included. Serial #7270 Good
Condition
1 ea S906040 Jetline LWHP-96Z 8 Powered Elevation Weld
Seamer. 104 total welding/clamping length capacity. 7.25 minimum
part diameter. 87 maximum part diameter (66.75 when using the
existing drum cradle). Hydraulic powered elevation of the welding bed
from the minimum height of 46 to a maximum of 92. Remote pendant
control for elevation, mandrel latching and finger clamping. Variable
speed rack and pinion driven carriage. Water cooled mandrel. Gas purge
back-up bar. Includes electric hydraulic pump and a drum cradle that
moves manually in and out on 16 of inverted angle iron track for
ease of loading up to 66 diameter tanks. Welding equipment NOT
included. Serial #990494 Very Good Condition!!
1 ea S100711 Cecil Peck 8 Weld Seamer. 96 total
welding/clamping length capacity. 8 minimum part diameter capacity.
42 maximum part diameter capacity (can be increased with a riser).
Variable speed rack and pinion driven carriage. Welding equipment NOT
included. Serial #n/a Good Condition
1 ea S100908P Weldline 8 Weld Seamer. 101 total
welding/clamping length capacity. 7 minimum part diameter capacity.
30 maximum part diameter capacity. Currently equipped with a
standard copper back-up bar, plate alignment devices, cable track,
3 manual horizontal slide, 3 manual vertical slide, manual
rotary slide, Weldline rack and pinion driven carriage and carriage
control, Thermal Arc Ultima 150 plasma power supply and plasma torch.
Reconditioned with existing equipment !!
1 ea S910004P Amet / Jetline 8 Vertical Variable Polarity
Seamer. System includes an Amet controller & operating console,
Amet Motor control center, An integrated Amet 500 VP power supply,
Custom gas control unit, 8 x 8 manipulator and 8 vertical
seamer bed, 4-roll wire feeder and all welding equipment. Purchased
New in 2002 for OVER $300,000.00 !! Please Ask for a Detailed
Specification Sheet !! Excellent Condition
1 ea S910003P Pandjiris / Hobart 8 Vertical Variable Polarity
Seamer. System includes an integrated Hobart VP-300S power supply, gas
control unit, 8 x 8 manipulator and 8 vertical seamer bed,
4-roll wire feeder and all welding equipment Please Ask for a Detailed
Specification Sheet !! Very Good Condition
1 ea S912009 Webb Model J-104 104 Welding Seamer. 104
clamping/welding length capacity. 8 minimum part diameter capacity.
32 maximum part diameter capacity. Rack and pinion driven variable
speed carriage. Cable tray. Water cooled back up bar. 6 manual
cross slides. Welding equipment NOT included. Serial #9X106A Good
Condition
1 ea S903001 Pandjiris 9 Weld Seamer. 114 total
welding/clamping length capacity. 7-1/2 minimum part diameter.
48 maximum part diameter. Variable speed rack and pinion driven
carriage. Water cooled mandrel. 5 x 5 manual cross slides.
Rotary slide. Welding equipment NOT included. Serial #25-1875 Good
Condition
1 ea S100601 Four Corp. Model 100-120 10 External Seam
Welder. 123 total welding / clamping length capacity. 10.5
minimum part diameter. 30 maximum part diameter ( can be increased
with a riser ). Variable speed rack & pinion driven carriage.
Serial #89-628 Good Condition
1 ea S807002 Jetline Model LWFS-120Z 10 Flat Sheet Seamer.
128 total welding/clamping length capacity. 1 Air lift bed for
ease of loading. Includes a Jetline SWC-6A carriage with a 9026
control with a digital ipm meter. 2 manual cross slides. Gas purge
back-up bar. Welding equipment NOT included. Serial #910315 Good
Condition
1 ea S807003 Pandjiris Mosel 120-L 10 Internal/Flat Sheet
Seamer. 126 Total welding/clamping length capacity. Variable speed
rack & pinion driven carriage with a model M-VSC control. 3
horizontal slide. Water cooled mandrel. Gas purge back-up bar. Welding
equipment NOT included. Good Condition
1 ea S704003 Pandjiris Model 120-1/50-FS 10 Internal / Flat
Sheet Seamer. 120 welding/clamping length. .020 to 3/8 clamping
range. For flat sheet or I.D. welding on cylinders with a 50
minimum I.D.. Linde model OM-48 variable speed travel carriage.
16.5 mandrel height. 6 wide Pandjiris 4-bar linkage clamp finger
arrangement (provides more clamping pressure and inward surge than
standard fingers). Gas purge back-up bar. 6 manual cross slides.
Welding equipment NOT included. Serial #25-3677 Good Condition
PLANISHERS
1 ea PL612004P Airline Model R40360 Longitudinal Weld Planisher.
For Planishing Flat Sheets or Cylinders up to 60" Long. .020
to 3/16" Thickness Capacity on Aluminum or Mild Steel ( 1/8"
Maximum Capacity on Stainless Steel ). 10" to 36" Cylinder
Diameter Capacity. Serial #R1050 Good Condition
PL704001 Weldmation Model TU-1921 Vertical Planisher. 1/8
thickness capacity. 9 stroke capacity. Ready for your custom
designed tooling. Serial #n/a. Very Good Condition
SIDE BEAM WELDERS
1 ea WS412001 Jetline Portable Heavy Duty Cast Long Length
Stellite Overlay System. Jetline TKK-24 Precision Screw Drive
(1-1/2 screw) Side Beam with 24 Travel. Heavy Duty 9-1/2
Power Vertical Slide, 8 of Z axis Manual Slide. Long Rod Feeder
with adj. dia. guide. Miller Oscillator with Center Line Steering.
Overall dimensions of Portable side Beam Assy. 76 high, 63 wide,
60 long. System includes Miller 300 amp Synchrowave welder and Tig
Torch. Excellent Condition!
1 ea SB507001 Linde 8 Side Beam Tig Welding System. 10
Side Beam with a Linde OM-48 Rack and Pinion Drive Variable Speed
Carriage for a Total Travel Length of 8. Portable Floor Mounting
Stantions for a Fixed Height of 59 to the Bottom of the Beam. 4
Manual Cross Slides and a Rotary Slide. Cyclomatic AVC-3 Arc Voltage
Control. Miller Weld Oscillator. Jetline CWF-10 Cold Wire Feeder. Good
Condition
1 ea SB504001P Jetline Model TKS-96 8 Powered Elevation
Side Beam. 124 Side Beam with 8 of Travel Length. Jetline SWC-3B
Variable Speed Travel Carriage. Powered Elevation from 12 to 68
to the Bottom of the Beam. Cyclomatic 4 x 4 Mechanical Seam
Tracker. Serial #R4356. Very Good Condition
1 ea SB506001 10 ft. Heavy Duty Custom Side Beam for Sub-Arc or
Mig Welding. Welding Length of 104. Variable Speed H.D. Rack and
Pinion Carriage. Dual 32 Horizontal Manual Cross Slides with 5
Vertical Manual Slides. Cross Slide System has a 6 Pneumatic Lift.
Good Condition
1 ea SB609007 Jetline PST-300 Twin Head Overhead Bridge Side
Beam. 8 of Variable Speed Travel on both Carriages Mounted on the
Bridge. 12 Variable Speed Travel on the Side Beam Carriage. 134
to the Bottom of the Side Beam. Welding Torches are Currently Mounted
on Dual Powered Slides that have a Total of 60 Vertical Travel.
Welding Equipment Includes 2 each Airco Pulse Arc II 550 CV Power
Supplies, 2 each Airco Med-40 Wire Feeders, 2 Each Miller Coolmate 4
Water Circulators, 2 each AWC 1,000 Power Assisted Wire Payoff Reels,
2 each Jetline 6 x 6 Automatic Seam Trackers and a Jetline
Jetstar Programmable Control. Good Condition
1 ea SB101213P Lincoln 14 Sub-Arc Side Beam. Lincoln TC-3
variable speed travel carriage that has 14 of travel along a 16
side beam. 59 high legs with bolt down bases attached to each end
of the side beam. Welding equipment includes a Lincoln NA-5 control,
NA-5 sub-arc head, 35 control cables, 35 welding cables, DC-600
power supply, Cyclomatic 5 x 5 mechanical seam tracker and a
Weld Engineering Model PFR-3000 flux recovery system. Just Out of
Service Quick Turn Around
1 ea SB110205 Lincoln 16 Powered Elevation Side Beam and
Carriages. A Lincoln 16 side beam with 2 each Lincoln TC-3 variable
speed travel cars. Powered elevation from 40 to 130 to the
bottom of the beam. 230 or 460 volt. Serial # n/a Ready to be
reconditioned to fit your needs
1 ea SB804003 Jetline Model TKMV240 Dual Carriage Side Beam.
240 Length. 2 each Jetline model SWC-6DZ rack and pinion driven
variable speed carriages. Mounting stantions and welding equipment NOT
included. Serial #969791 Very Good Condition
1 ea SB302001 Pandjiris GB PBT 12 20' Side Beam Welding System.
3 ea. Model 60 Stanchions, VSC-21-12 Variable Speed Carriage, Miller
Automatic 1 Head Timers and 4-roll Feed Head, Cyclomatic Seam Tracker,
3 Axis Manual Cross Slides. Pulse Arc Control, This is a Factory
Integrated System With all Equipment Mounted and Interfaced on
Carriage Good Condition
1 ea SB812002 Bancroft 22 Side Beam. 20 travel. Rack &
pinion driven variable speed carriage. Mounting stantions and welding
equipment NOT included. Good Condition
1 ea SB502001 Jetline TK312 26 Tig Welding Side Beam. 28
Side Beam with 26 of Travel, 50 High Floor Mount Stantions and a
Jetline Model 9026 Carriage Control with a Travel IPM Meter. Welding
Equipment to Include the Following: a Cyclomatic AVC-3 Arc Voltage
Control, a Jetline Model 9029 Cold Wire Feeder with a Micro Wire Feed
Head, a Cyclomatic 80A Magnetic Arc Oscillator, 5 Manual Horizontal
Slide and a 25 Powered vertical Slide. Serial #920516. Excellent
Condition
1 ea SB905002 Webb Model U-8 34 Powered Elevation Swing Arm
Side Beam. 34 side beam with a Lincoln model TC-3 travel car for a
total of 30 travel. Powered elevation for a work diameter capacity
from 2 to 8. Electric/hydraulic powered swing out arms to move
the side beam 40 out from the elevation supports for ease of
loading and unloading. Serial #67115 Good Condition
WELDING LATHES
1 ea L604009 Custom 12 GTAW Welding Lathe. 6-12 Part
Length Capacity. 9 Maximum Diameter Capacity. 6 Stroke Pneumatic
Tailstock. 5 Pneumatic Torch Lifter. All Functions Controlled by an
Allen-Bradley SLC-500 Programmable PLC. Rotary Ground. Welding
Equipment Includes a Powcon 150STP Power Supply and a 120 amp Air
Cooled Tig Torch. Serial # N/A Good Condition
1 ea L100413 Contour Arc Model FW Welding Lathe. 26 length
capacity. 14.5 diameter capacity. 200 lb weight capacity. Miller
S-60 series Wire Feeder. 115 volt. Serial #141 Good Condition
1 ea L708010 Bancroft Model 605 Dual Head Welding Lathe. 14
Maximum length capacity. 14 Maximum diameter capacity. 800 lb load
capacity. Variable speed rotation from 1 to 20 RPM. Weld overlap
timer. 2 each mig welding heads that each include a Bancroft wire feed
system, 4 Vertical and 4 horizontal cross slides and air torch
lifters. 120 volt Serial #3565/115-990 Good Condition
1 ea L708011 Bancroft Model 605 Dual Head Welding Lathe. 14
Maximum length capacity. 14 Maximum diameter capacity. 800 lb load
capacity. Variable speed rotation from 1 to 20 RPM. Weld overlap
timer. 2 each mig welding heads that each include a Bancroft wire feed
system, 4 Vertical and 4 horizontal cross slides and air torch
lifters. 120 volt Serial #3565/115-990-1 Good Condition
1 ea L708013 Bancroft Model 605 Single Head Welding Lathe. 14
Maximum length capacity. 14 Maximum diameter capacity. 800 lb load
capacity. Variable speed rotation from 1 to 20 RPM. Weld overlap
timer. Bancroft wire feed system, 4 Vertical and 4 horizontal
cross slides and air torch lifters. 120 volt Serial #3558/115-980 Good
Condition
1 ea L809002 Compak-o-matic Model 1027-101 19.5 x 42 Mig
Welding Lathe. 19.5 maximum diameter capacity. 42 maximum length
capacity. 7 pneumatic torch lifter. 8 stroke pneumatic
tailstock. 600 amp rotary ground. Wire feed head. Welding power supply
NOT included. Serial #HR149 Good Condition
1 ea L809004 Compak-o-matic Model 1010 20 x 20 Mig Welding
Lathe. 20 maximum diameter capacity. 20 maximum length capacity.
7 pneumatic torch lifter. 5.5 stroke pneumatic tailstock. 3
vertical torch adjuster. 2 horizontal torch adjuster. 600 amp
rotary ground. Wire feed head. Welding power supply NOT included.
Serial #HG-113 Good Condition
1 ea L708009 Bancroft Model 1208 30 Degree Incline Rotary
Welder. 800 lb Weight capacity. 44 Maximum Diameter Capacity.
Welding bed is fixed at a 30 degree angle. .01 to 10 RPM variable
speed rotation. Weld overlap timer. Miller 60 series wire feed system
with vertical and horizontal croos slides and an air torch lifter. 120
volt. Serial #3334/110-086 Good Condition
1 ea L608004 Jetline 14 x 14 Mig Welding Lathe. 14 Part
Diameter Capacity. 14 Length Capacity. Jetline ZB-100 Positioner,
100 lb Weight Capacity. Air Actuated Tail Stock for Part Clamping.
Vertical, Horizontal and Rotary Cross Slides. Miller 300 amp Power
Supply. 230/460 Volt. Serial #910424 Good Condition
1 ea L705007 Jetline ZB-100B Benchmaster Welding Lathe. 16
diameter capacity. 17 maximum length capacity. 100 lb weight
capacity @ 4 C.G.. Variable speed travel from .1 to 5.0 rpm. 7
diameter 3-jaw self centering chuck. Jetline Model 3018 Base. Jetline
4501A torch holder. Jetline 1016A cross slides. Jetline TS-200B air
actuated tailstock. On/off foot pedal. 115 volt. Serial #87401 Very
Good Condition
1 ea L601001 Jetline Model CWP-24 90 Degree Power Tilting Lathe
Bed. 200 lb Weight Capacity. 20.5 Length Capacity. 12 Diameter
Capacity. For use as a Vertical or Horizontal Welding Lathe with a 90
Degree Powered Tilting Bed. 8 Capacity Chuck with a 1/2 thru
hole for back purging. 3 Air Actuated Tailstock for Part Clamping.
Jetline ALC101-V4T Arc Length Controller. Jetline Model 9024-101
Circumferential Tig Weld Sequencer. Variable Speed Torch Carriage for
Either Circumferential or Longitudinal Welding. Powered Torch Lifter.
Powered Slides. 115 volt. Serial #920131 Good Condition
1 ea L906036 Quest 26 Dual Torch Welding Lathe. 26 maximum
part length capacity. 18 maximum part diameter capacity. 6
stroke pneumatic clamping. Variable speed rotation. 2 each manual
adjustable torch mounts. 2 each Miller 60 series feeders. Power
supplies NOT included. 115 volt. Serial #n/a Good Condition
1 ea L906035 Quest 33 Dual Torch Welding Lathe. 33 maximum
part length capacity. 20 maximum part diameter capacity. 6
stroke pneumatic clamping. Variable speed rotation. 2 each manual
adjustable torch mounts. 2 each Miller 60 series feeders. Power
supplies NOT included. 230 or 460 volt. Serial #n/a Good Condition
1 ea L906033 Quest 36 Dual Torch Welding Lathe. 36 maximum
part length capacity. 16 maximum part diameter capacity. 6
stroke pneumatic clamping. Variable speed rotation. 2 each manual
adjustable torch mounts. 2 each Miller 60 series feeders. Power
supplies NOT included. 230 volt. Serial #n/a Good Condition
1 ea L906034 Quest 46 Dual Torch Welding Lathe. 46 maximum
part length capacity. 30 maximum part diameter capacity. 6
stroke pneumatic clamping. Variable speed rotation. 2 each manual
adjustable torch mounts. 2 each Miller 60 series feeders. Power
supplies NOT included. 115 volt. Serial #n/a Good Condition
1 ea L110105P Custom 54 Dual Head Mig Welding Lathe. 54
length capacity. 44 diameter capacity. Air actuated tailstock. 2
each manual travel cars. Air torch lifters 2 each Cyclomatic 6 x
6 seam trackers. 2 each Miller Deltaweld 650 power supplies with
Auto 1D-DW controls and A1D-2 feed heads. Serial #n/a Reconditioned
with existing welding equipment
1 ea L803015 Weldlogic Model CWT-102 Weld Lathe. 200 lb weight
capacity. 13 length capacity. 12 maximum part diameter capacity.
6 diameter 3-jaw self centering chuck. Arc length control.
Weldlogic Pulsarc 300-STD DC power supply. Pendant Control. Serial
#523 Good Condition
1 ea L804004 Merrick Engineering 64 GTAW Welding Lathe. 12
Maximum part diameter. 64 Maximum part length, 98 side beam with
manual spotting car. Merrick Volt Track II arc voltage control. Cold
wire feeder, 2 manual cross slides. 360 degree rotary slide. Serial
#N/A Good Condition
1 ea L512002 Bancroft High Capacity 3 Station, Dual Torch,
Indexing Welding Lathe. 23 Length Capacity, 12 Diameter
Capacity. 3 Position Indexing Turret for Loading of Parts, Welding of
Parts and Cooling of Parts. 2 Torches for Welding on both Ends of
Parts. GMAW Welding Equipment Includes 2 each Miller S-62 Wire Feeders
with Tweco Water Cooled Auto Guns on 4 Bancroft Retractable Air
Slides. Serial #3327/109-843 Good Condition
1 ea L100408 Bancroft VHI-18 Vertical Lathe. 30 length
capacity between the headstock and the tailstock (currently equipped
with an air clamping fixture that limits the length to 11). 8
diameter capacity with the current torch mount (the mount could be
altered to accommodate a diameter of 35). 400 lb weight capacity. A
synchronized rotary drive rotates the opposing vertical spindles at
the same speed. This maintains the radial alignment between two parts
with no chance of slippage. Welding equipment NOT included. 230 or 460
volt. Serial #3829/122-106 Good Condition
1 ea L100409 Bancroft VHI-18 Vertical Lathe. 30 length
capacity between the headstock and the tailstock (currently equipped
with an air clamping fixture that limits the length to 11). 8
diameter capacity with the current torch mount (the mount could be
altered to accommodate a diameter of 35). 400 lb weight capacity. A
synchronized rotary drive rotates the opposing vertical spindles at
the same speed. This maintains the radial alignment between two parts
with no chance of slippage. Welding equipment NOT included. 230 or 460
volt. Serial #3899/124-001 Good Condition
1 ea L100410 Bancroft VH-18 Vertical Lathe. 30 length
capacity between the headstock and the tailstock (currently equipped
with an air clamping fixture that limits the length to 11). 8
diameter capacity with the current torch mount (the mount could be
altered to accommodate a diameter of 35). 400 lb weight capacity. A
synchronized rotary drive rotates the opposing vertical spindles at
the same speed. This maintains the radial alignment between two parts
with no chance of slippage. Welding equipment NOT included. 230 or 460
volt. Serial #3820/121-347 Good Condition
1 ea L100411 Bancroft VHI-18 Vertical Lathe. 30 length
capacity between the headstock and the tailstock (currently equipped
with an air clamping fixture that limits the length to 11). 8
diameter capacity with the current torch mount (the mount could be
altered to accommodate a diameter of 35). 400 lb weight capacity. A
synchronized rotary drive rotates the opposing vertical spindles at
the same speed. This maintains the radial alignment between two parts
with no chance of slippage. Welding equipment NOT included. 230 or 460
volt. Serial #3826/122-103 Good Condition
1 ea L100412 Bancroft VH-18 Vertical Lathe. 30 length
capacity between the headstock and the tailstock (currently equipped
with an air clamping fixture that limits the length to 11). 8
diameter capacity with the current torch mount (the mount could be
altered to accommodate a diameter of 35). 400 lb weight capacity. A
synchronized rotary drive rotates the opposing vertical spindles at
the same speed. This maintains the radial alignment between two parts
with no chance of slippage. Welding equipment NOT included. 230 or 460
volt. Serial #3572/116-145 Good Condition
1 ea L305001 Bancroft Model VH-24 Welding Lathe. 33" Long x
48" Diameter Capacity. Pneumatic Torch Lifter, Forward and
Reverse Variable Speed, Weld Overlap Timer and a Miller 60M Control
and Feed Head Serial #3609-(117-212) Good Condition
1 ea L305002 Bancroft Model VH-24 Welding Lathe. 33" Long x
48" Diameter Capacity. Pneumatic Torch Lifter, Forward and
Reverse Variable Speed, Weld Overlap Timer and a Miller 60M Control
and Feed Head Serial #3610-(117-213) Good Condition
1 ea L206001P Stoody Screw Flight Tig Hard Surfacing Lathe.
Capacity of 7" Diameter (may be increased) x 144" Long. This
Machine was used for Hard Surfacing with #6 CoCrA Solid Lengths. Has
Oscillating Head, Preheat System, Control Console and 500 amp Miller
DC Power Supply. AS-IS Only !
1 ea L9912001 Bancroft Welding Lathe. Work Piece Capacity 24
X 72. Bed 12 Overall, Tailstock has Air Cylinder for part
clamping. Linde Automatic Head w/Cross Slides. Variable Speed Rotation
For/Rev. As-Is or Re-conditioned to Proper Working Order.
1 ea L610002 Jetline Model CWL-72 Lathe and 13 Side Beam. 500
lb Capacity Variable Speed Headstock / Tailstock. 30 diameter
Capacity. 72 Length Capacity (Can Increased to 48 - 120
Capacity with a Spacer). 13 Side Beam with a Manual Spotting Car
that has 126 of Travel. Welding Equipment Includes a Jetline
Model 9500 System Control, ALC-201V6E Arc Length Control, Rotary Slide
and Horizontal Slide. Serial #81322 Good Condition
1 ea L1054413 Melton Model 6330 Single Torch Welding Lathe.
Capacity30 dia. X 37 long. Programmable A.B. SLC 500 Control.
Pneumatic Fixture Clamping. Miller Maxtron 450 Pulse Welding System
with Automatic 1DA Control & Head. Welding system completely
integrated. Safety Light Curtain, Operator Console w/Palm Buttons.
Automatic Leather Curtains. Hood for exhaust. Complete, ready for your
fixturing. 1993 Very Good Condition
1 ea L101014 Pandjiris 84 Dual Head Welding Lathe. 84
maximum length capacity. 14 to 32 diameter capacity. Air
actuated tailstock mounted on a manual travel car. 10 side beam
with 2 manual travel cars each with motorized vertical and horizontal
adjusters. Air actuated grounding rollers mounted on a manual
adjustable height beam. Welding equipment includes 2 each of the
following: Miller Invision 456P power supplies, Miller Automatic M
controls and feed heads and a Jetline Model JST-250F-10x10 laser seam
trackers. A unique system used in the manufacturing of aluminum truck
fuel tanks. Ready to be reconditioned to fit your needs
1 ea L502001 Centurion Model WL24X168 Welding Lathe. 24
Diameter Capacity. 168 Length Capacity. Variable Speed Travel Car
and a Manual Spotting Car. Pandjiris Model A 31-1/4 Capacity
Gripper Chuck. Manual Tailstock Mounted on a Powered Travel Car.
Powered Elevation Side Beam. Includes a Lincoln DC-600 Power Supply
with a NA-3N Sub-Arc System. Good Condition
1 ea L110203 L.A.G. Industries Dual Sided Welding Lathe. 24
Lincoln side beam with 2 each Lincoln TC-3 variable speed travel
carriage. 80 height of the bottom of the beam. A dual sided
variable speed headstock that sits on a manual travel car on 26.5
of track. 2 ea live center idlers mounted on manual travel cars. All
travel cars lock into place every 2.75. Maximum combined length
capacity of 16.5. 43 height to the center of the rotational axis
off the floor. Lathe has a swing capacity of 52. System includes 2
each Lincoln DC-1000 Power supplies with NA-5 controls and heads.
Previously used to overlay 2 steel mill rolls at a time. Serial #n/a
Ready to be reconditioned to fit your needs
1 ea L110204 L.A.G. Industries Dual Sided Welding Lathe. 22
Lincoln side beam with 2 each Lincoln TC-3 variable speed travel
carriage. 80 height of the bottom of the beam. A dual sided
variable speed headstock that sits on a manual travel car on 26.5
of track. 2 ea live center idlers mounted on manual travel cars. All
travel cars lock into place every 2.75. Maximum combined length
capacity of 16.5. 43 height to the center of the rotational axis
off the floor. Lathe has a swing capacity of 52. WELDING EQUIPMENT
NOT INCLUDED. Previously used to overlay 2 steel mill rolls at a time.
Serial #n/a Ready to be reconditioned to fit your needs
1 ea L901028 Jetline Model CW5-192Z Lathe Bed. 5,000 lb weight
capacity. Variable speed rotation. 29 minimum to a maximum of
192 length capacity. 60 maximum part diameter capacity.
Tailstock is mounted on an electric / hydraulic driven(Includes
hydraulic pump system) rack and pinion drive travel car. Side beam and
carriage NOT included. Very Good Condition
1 ea L912003 Jetline CW5-244 Welding Lathe. 5,000 lb turning
capacity. 240 length capacity. 57 diameter capacity. 22.5
side beam with a variable speed rack & pinion driven carriage and
cable tray for all cables.. Manual adjustable tailstock with an air
actuated centering head. Current welding equipment includes a Lincoln
DC-655 power supply, NA-5 sub-arc control and feed head, 10 x 10
Cyclomatic cross slides. Serial #81246 Good Condition
SPUD
WELDER - CIRCLE WELDERS & WELD A-ROUNDS
1 ea C110106P Custom Weld-a-Round. 40 square work table. 4
to 24 diameter capacity. 300 degree variable speed torch rotation.
5 air powered part clamping. 230 volt. As-Is Working Condition
1 ea C100905 Circle Welding Innovations Model RW-1500 Nozzle
Welder. 1 to 18 diameter capacity. .035 to 5/64 wire diameter
range. 500 amp welding current capacity. System includes a standard
rise & fall cam, amp meters, torch angle adjuster, heavy duty
horizontal and vertical adjusters and wire reel assembly. Welding
control functions include auto weld switch, wire direction switch,
cold wire inch, purge switch, pre flow, post flow and burn back timer.
115 volt. Serial #1081439 Good Condition
1 ea C100402 Cypress CWG-1100 Circular Welder. 10 to 50
diameter capacity. Variable speed from .06 to 72 IPM. Rise & fall
range from 0 to 7. 400 amp 60% duty cycle. Vertical &
horizontal torch adjusters. Burn back control. 120 volt. Serial
#C010904 Good Condition
1 ea C100401 Bancroft Model 500 Weld-a-round. 150 lb clamping
force. Adjustable 8 vertical stroke. Rack and pinion torch adjuster
0.7 to 14 RPM rotational speed. 500 amp rotary ground. Water cooled
torch. Air powered arc screen lifter. 50-550 ipm integral Miller S-60
wire feeder. 120 volt. Serial #3657-1/118-012 Excellent Condition
1 ea C608003 Compakomatic Model 1025 Rotomatic Mig Weld-A-Round.
0 to 6 Diameter Capacity. Manual Adjustable Height. Variable Speed
from .30 to 15 RPM. Adjustable Rotational Overlap from 0 to 360
Degrees. 6 Air Torch Lifter. Model 375 Rotational Control. 600 amp
Current Capacity. Miller 300 amp Power Supply. Serial #GM-154 Good
Condition
1 ea C804006 Compakomatic Model 920E Weld-a-Round. 8 maximum
part diameter. 13 maximum part height (can be increased with a
riser). 7 pneumatic torch lifter. Compakomatic series 400 control.
115 volt. Serial #GM241 Good Condition
1 ea C604008 Machine Technologies GTAW Weld-a-Round. 12 Part
Diameter Capacity. 6 Part Height Capacity (Can be Increased with a
Torch Riser). 1 Vertical Torch Lifter. Weld Over Lap Timer. All
Functions Controlled with a Programable PLC. Welding Equipment
Includes a 1994 Miller Maxstar 152 with Snap Start, Miller Water
Circulator and a 250 Amp Water Cooled Tig Torch. Serial #1-549-2 Good
Condition
1 ea C508001 Rumble Automation Weld-A-Round Circular Spud
Welding Station. 5 Vertical Stroke. Variable Speed Torch Rotation
by a 3 Turn Potentiometer. 36 High Work Table. 32 Part Diameter
Capacity. 6 Diameter Weld Capacity. Currently Equipped with a
Hobart Auto-CVS Wire Feeder. Power Supply NOT Included. 575 volt.
Serial #100-64-3712 Good Condition
1 ea C110314 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most Popular Stationary Circular
Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb
Clamping Force. 8 Vertical Stroke. 0.7 to 14 RPM Travel Speed.
Bench Mounted. Welding Equipment NOT Included. Serial #3913/124-015
Ready to be reconditioned to fit your needs
1 ea C110313 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most Popular Stationary Circular
Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb
Clamping Force. 8 Vertical Stroke. 0.7 to 14 RPM Travel Speed.
Bench Mounted. Welding Equipment NOT Included. Serial #4239/130-857
Ready to be reconditioned to fit your needs !
1 ea C110312 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most Popular Stationary Circular
Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb
Clamping Force. 8 Vertical Stroke. 0.7 to 14 RPM Travel Speed.
Bench Mounted. Welding Equipment NOT Included. Serial #4269/131-212
Ready to be reconditioned to fit your needs !
1 ea C110311 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most Popular Stationary Circular
Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb
Clamping Force. 8 Vertical Stroke. 0.7 to 14 RPM Travel Speed.
Bench Mounted. Welding Equipment NOT Included. Serial #3914/124-016
Ready to be reconditioned to fit your needs !
1 ea C612015 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most Popular Stationary Circular
Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb
Clamping Force. 8 Vertical Stroke. 0.7 to 14 RPM Travel Speed.
Welding Equipment NOT Included. Serial #50359-10 Good Condition
1 ea C612014 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most Popular Stationary Circular
Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb
Clamping Force. 8 Vertical Stroke. 0.7 to 14 RPM Travel Speed.
Equipped with rise and fall option. Welding Equipment NOT Included.
Serial #50123-01 Good Condition
1 ea C609008 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most Popular Stationary Circular
Welding System in the Welding Industry. 300 Amp Ground Capacity. 75 lb
Clamping Force. 8 Vertical Stroke. 0.7 to 14 RPM Travel Speed.
Bench Mounted. Welding Equipment NOT Included. Serial #N/A Good
Condition
1 ea C906001 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most popular stationary circular
welding system in the welding industry. 300 Amp ground capacity. 75 lb
clamping force. 8 vertical stroke. 0.7 to 14 RPM travel speed.
24 diameter round table. Welding equipment NOT included. Serial
#n/a Good Condition
1 ea C101006 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most popular stationary circular
welding system in the welding industry. 300 amp ground capacity. 75 lb
clamping force. 8 vertical stroke. 0.7 to 14 RPM travel speed.
Lincoln V-300 Pro power supply Serial #8448-2 Completely Reconditioned
and Ready to Ship
1 ea C101005 Bancroft Weld-A-Round 300 Circular Spud
Welder. The Weld-A-Round 300 is the most popular stationary circular
welding system in the welding industry. 300 amp ground capacity. 75 lb
clamping force. 8 vertical stroke. 0.7 to 14 RPM travel speed. Rise
and fall cam. Welding equipment NOT included. Serial #50359-10 Ready
to be reconditioned to fit your needs !
1 ea C512001 Bancroft 350 High Capacity Dual Head, 3 Station
Indexing Weld-a-Round. Bancroft is the Manufacturer of the Most
Popular Stationary Circular Welding System in the Welding Industry.
Both Weld Stations have 8 Vertical Stroke with a 150 lb Clamping
Force and Variable Speed Torch Rotation from 0.7 to14 RPM. 300 amp
Capacity. A 3 Position Indexing Table for Loading of Parts and Welding
Under 2 Separate Weld Stations. Can be Used for 2 Passes on One Part
or One Pass on Two Individual Parts with Proper Fixtures. Currently
Set up for GTAW Application. Serial #3300/109-003 Good Condition
1 ea C501001 WeldLogic CWT-12-15V Vertical Welding Positioner.
Precision Vertical Positioner with Self-Centering 3 Jaw Chuck, 6
Dia. Torch Holder Post with Pneumatic Torch Retract. 100 lb Capacity.
Serial #CWT-12SN9413 Very Good Condition
1 ea C903003 WeldLogic CWT-12C Circular Dual Torch Vertical
Welding System. 10 maximum part diameter capacity. Precision
variable speed 100 lb capacity vertical positioner. Dual torches
mounted on 11.5 vertical torch slides for a torch height from
9.5 to 21 and 3.5 vertical slides. System includes 2 each
AWS-150 DC constant current power supplies with air cooled tig
torches. Remote control for all functions. 115 or 230 volt. Serial
#00211780 Good Condition
1 ea C412001 Alloy Custom Circular Welder. 75 lb Capacity,
Variable Speed (0.8 50 RPM) 4 3-Jaw Chuck, Lever Actuated
Gravity Type Part Hold Down Mounted on 6 Slide. 6 Maximum Part
Diameter, 6 Maximum Part Height. 3 Axes of Torch Adjustment.
Analogue Weld Control 10 Turn Potentiometer for Accurate Speed
Control, Start/Stop w/ E-Stop, Forward/Reverse. Manual Flip-down 4
x 5 Shaded Lens for Weld Viewing Good Condition
1 ea C205002 Alltra Corporation Model VWL2436 Circular Welder.
Vertical Lathe with an 18" Part Diameter Capacity, 24" Part
Length Capacity and an Air Actuated Centering Head. A Complete System
that Includes a Lincoln DC-400 CC/CV Power Supply, Lincoln NA-5R Head
and Control with a Lincoln Analog Interface Procedure Control, Miller
Coolmate 4 Water Circulator, 20" Motorized Horizontal and
Vertical Cross Slides, Allen-Bradley SLC5/04 Control and Allen-Bradley
Panelview 1400 Monitor with Operator Friendly Touch Screen
Programming. Manufactured in 1998. Serial #2211 Excellent Condition
1 ea C912010 Cecil Peck Circular Welder. Manual Table Lift. No
Table. 1" to 6" Diameter Capacity. Variable Speed Rotation.
Pedestal Control Console for all Functions. No Welding Equipment.
Serial #N/A Good Condition
1 ea C805022 Cecil Peck Circular Welder. Hand Wheel Table Lift.
1 to 6 welding diameter capacity. 43 part diameter capacity.
Variable Speed Rotation. Pedestal Control Console for all Functions.
Welding equipment NOT included. Serial #n/a. Good Condition
1 ea C406001P Cecil Peck Circular Welder. Manual Table Lift. No
Table. 1" to 6" Diameter Capacity. Variable Speed Rotation.
Pedestal Control Console for all Functions. No Welding Equipment.
Serial #N/A As Is Price
1 ea C204001 Cecil Peck Circular Welder. Hand Wheel Table Lift.
36" x 30" Tee Slotted Table. Variable Speed Rotation.
Pedestal Control Console for all Functions. Equipped with a Lincoln
NA-2 Submerged Arc Control and Welding Head and a R3S-600 Power
Supply. Serial #69203 Good Condition
1 ea C906037 Quest Large Capacity Weld-A-Round. 14 maximum
part height capacity. 1 to 36 part diameter capacity. 6
pneumatic stroke clamping. Digital speed tachometer. Currently
equipped with a Miller Deltaweld 652 power supply and a S-62 series
feeder. 230 or 460 volt. Serial #n/a Good Condition
ORBITAL TUBE/PIPE WELDERS
1 ea TW303003 Arc Machines Model M-115 Orbital Pipe Welding
Power Supply. 300 amp, 60% duty cycle, 230/460, 3-phase, Built in
Water Re-circulating Unit. Current Pulse, Wire Pulse and Weld
Oscillation Controls Fair Condition, As Is Only Price
1 ea TW1011002 Arc Machines Model 215, Orbital Tube to Tube
Welder. Includes: Model 215- OP Operator Control, Cables etc. Weld
heads NOT Included ! Ser. #4074 "1988" Exc. Condition
1 ea ARC 109 1 Arc Machines, Inc. Model 109-1, Tube to Tube
Welder. "1982" Ser.# 513, Includes: 1 ea 09-1000 Head
for 1" Max. Dia. Tube. Built-In Water Re-Circulating Unit. As-Is
Only !! Good Condition
1 ea ME612008 George Fischer Model RA-2 Pipe Cutting / Beveling
Machine. Outside Diameter Range from Ό" to 2" Pipe,
Wall Thickness up to .217". Cuts Square to Within .005". 115
Volt. Serial #30394 Good Condition
1 ea TW209002 Tri-Tool Model 202TS. Pneumatic Tube to Tube
Sheet Facing Tool. Complete with Collets for Tubing from .77 to 1.95
I.D. Serial #1197007 Good Condition
1 ea ME606007 Tri Tool Model 572E Tube Squaring Machine.
Ό"
to 2" Tube Diameter Capacity. 115 volt. Serial # N/A Good
Condition
1 ea ME606010 Tri Tool Model 574E Tube Squaring Machine.
1" to 4" Tube Diameter Capacity. 115 volt. Serial #1194067 Good
Condition
1 ea ME606015 Mathey Dearman Model 48 Porta-Mill Portable Pipe
Cutting & Beveling Machine. 3.375 to 8.125 I.D. Pipe Diameter
Range Capacity. ½" Maximum Face or Bevel Capacity. Power Unit
NOT Included. Works with Rothenberger USA, Mini-Collins and Ridgid
Universal Power Drives. Serial # N/A Good Condition
NEW
AUTOMATED WELDING SYSTEMS
GEN PT200B DIY S 06 NEW Gentec Type S Circular Welding
System. A Gentec 330 lb capacity @ 2" c.g. positioner,
Variable speed rotation from0 to 4.0 RPM, 90 degree manual hand wheel
tilt mounted on a DIY-S-06 accessory kit that includes a CB-002
control, 24" base rail, 20" mounting rail, adjustable torch
holder with 2" cross slides and pneumatic torch lifter. Mounted
on the positioner is a 19-5/8" capacity 3-jaw self centering
chuck. 115 volt. NEW !
USED
AUTOMATED WELDING SYSTEMS
1 ea WS909006 1996 Cypress
Sprinkler Fabrication System. This 26 system includes the following
: 1 ea Model CB-10P Cypress plasma cutting head with a Thermal
Dynamics Signature 1250 cutting system mounted on a manual travel car,
1 ea Model CW-5 Cypress welding head with a Lincoln DC-600 power
supply and a pendulum type weld oscillator mounted on a manual travel
car, 1 ea 26 long side beam with 4 each bolt down mounting
stations. Very Good Condition
1 ea WS901021 Pandjiris Stationary
Manipulator Arm and Unit Frame Turning Roll System. A Pandjiris
stationary manipulator arm with a fixed height of 45.5 under the
arm and a length capacity of 40. The turning rolls have a 68,000 lb
turning capacity. 7 to 14 diameter capacity with a fixed axel
center of 72. Variable speed rotation. 5 sets of 5 wide x 20
diameter rubber wheels spaced over the 30 length of a variable
speed travel car that runs on 69 gauge rail track. Welding
equipment can be mounted on the end of the manipulator arm for
internal longitudinal or circumferential welding on cylinders. 460
Volt. Serial #66-4595 Good Condition
1 ea WS901022 Pandjiris Stationary
Manipulator Arm and Unit Frame Turning Roll System. A Pandjiris
stationary manipulator arm with a fixed height of 45.5 under the
arm and a length capacity of 40. The turning rolls have a 68,000 lb
turning capacity. 7 to 14 diameter capacity with a fixed axel
center of 72. Variable speed rotation. 5 sets of 5 wide x 20
diameter rubber wheels spaced over the 30 length of a variable
speed travel car that runs on 69 gauge rail track. Welding
equipment can be mounted on the end of the manipulator arm for
internal longitudinal or circumferential welding on cylinders. 460
volt. Serial #n/a Good Condition
1 ea WS809001 Compak-o-matic Model
440A 6 Linear Dual Torch Mig Welding System. 6 maximum welding
length. Dual torch with up to 13 between the torch heads. 6
manual in/out slide for fine adjustment. 3 manual right/left fine
adjuster. 6 stroke in/out indexing table for loading and unloading.
System includes 2 wire feeders and system controller. Welding power
supplies NOT included. Serial #GY211 Good Condition
1 ea WS704015 Hobart Manipulator /
Positioner TIG Welding System. Includes a 1,500 lb capacity @ 4 C.G.
positioner with power tilt and variable speed rotation. Positioner is
mounted on a manual travel car with 2 travel. Manipulator has
powered lift from 30 to 90, manual reach from 35 to 59
from the center of the mast. And a 6 horizontal adjuster. Current
welding equipment includes a Jetline model ALC- 401-6 Arc Length
control and model 9629 controller and a Jetline CWF-10A cold wire
feeder. All equipment mounted into a single skid frame base. Serial
#41-1641.Very Good Condition
1 ea WS703010 Cissel 12 x 4
Submerged Arc Welding Gantry. 12 variable speed rack and pinion
driven carriage. 4 variable speed Lincoln TC-3 carriage on the
cross boom. Complete Lincoln NA-5 sub arc package. Serial #111978 Good
Condition
1 ea WS702002 Weldlogic
Positioner/Tig Welding System. A Weldlogic 200 lb capacity positioner
with a 12 capacity chuck integrated with a Weldlogic complete GTAW
welding system. Welding system includes a Weldlogic RPW-2000 power
supply, Weldlogic cold wire feeder, Weldlogic arc length control,
Weldlogic weld oscillator and pendant control for programming all
functions. 230 volt. Serial #9914760 Good Condition
1 ea WS702003 Weldlogic
Positioner/Tig Welding System. A Weldlogic 200 lb capacity positioner
with a 12 capacity chuck integrated with a Weldlogic complete GTAW
welding system. Welding system includes a Weldlogic RPW-2000 power
supply, Weldlogic cold wire feeder, Weldlogic arc length control,
Weldlogic weld oscillator and pendant control for programming all
functions. 230 volt. Serial #9730194 Good Condition
1 ea WS604010 1996 Weldline
/ Miller GTAW Circular Welding Station. Weldline Automation Model WA-2
200 lb Capacity Positioner with a ½ to 16 Capacity 3-Jaw Chuck,
Weldline 6 Arc Length Control, Weldline Weld Sequence Control,
Weldline Cold Wire Feeder, 4 Manual Cross Slide and Rotary Slide.
Pneumatic part Clamping. Welding equipment Includes a Miller XMT-304
Inverter Power Supply, Miller HF-251D-1 High Frequency Arc Starter,
Miller PC-300 Pulse Control, Tweco TC900 Water Circulator and a
Weldcraft WP-27 500 amp Water Cooled Tig Torch. Serial # N/A Good
Condition
1 ea WS601002 Arc Systems
Automatic Pipe Welding System. System Includes a Preston-Eastin HS-2S
2,000 lb Capacity @ 6 C.G. Headstock with a 20 Diameter Scroll
Chuck that has a 6-1/2 Thru Hole. A Weldlogic AWS-150 Advanced Tig
Welding System that Includes Controls for Variable Speed Rotation of
Headstock, Weld Current Control, Arc Distance Control, Cold Wire Speed
Control and Feeder and a 1.0 to 150 amp DC Power Supply 3 eacg 6
Manual Slides for 3 Axis Adjustment of Torches. All Controls are
Mounted in a Single Remote Pendant Control. 230/460 Volt. Serial
#HS2S-13 Good Condition
1 ea WS509001 Pandjiris 1998
Hot Wire Tig Pipe Welding Station. A Complete Hot Wire Tig Pipe
Welding Station that Includes a Pandjiris 4 x 4 Manipulator on
Travel Car, 2 each Pandjiris HS-20PE-VS Headstocks with TJ-20 Chucks,
Pandjiris Pipe Supports on Manual Travel Cars, Miller / Jetline
Welding Package and a Complete set of 50 Tracks. Please Ask for a
Detailed Specification Sheet. Excellent Condition
1 ea WS507001 Mark Five
Manipulator/Turntable System. Turntable : 1,000 lb Capacity, 20
High. 24 Diameter Table with Slots. Variable Speed Drive from .01
to 1.4 RPM. The Manipulator if Fixed Over the Turntable with a Manual
Lift of 34 from 5.25 to 39.25 above the table and a Manual
Reach of 24. Serial #JN-1189 Good Condition
1 ea WS404001 Ransome Positioner /
Manipulator / Sub-Arc Welding System. System Includes a Ransome 5P 500
lb Cap. @ 6" C.G. Positioner (Ser. #1314851) with Power Tilt,
Variable Speed Rotation and Manual Height Adjustment. A 3JC40 40"
Diameter 3-Jaw, Self-Centering Welding Chuck. A Ransome Model 99
Manipulator (Ser. #9526562) with 72" Power Elevation from 0 to
71" at the Torch, Fixed Boom with a Manual Spotting Car from
44" to 88" from Center of the Mast, Manual Mast Rotation. A
Complete Lincoln DC-600 Sub-Arc System with NA-5 Control, Weld Head
And A Invincible Flux Recovery System. Very Good Condition
1 ea S412001 Cecil Peck Dual
Position Outside Corner Seam Welder. This Machine was Used to Tig
Weld the Outside Corners of Aluminum, Steel and Stainless Electric
Panel Boxes. The Dual Operator Positions were Used for Weld Lengths up
to 17 Long. The Air Clamping Device and Copper Mandrel Plates Could
be Increased (Within Reason) for Longer Welds. The Torch Carriers are
Heavy Duty Variable Speed Devices that are ½ H.P. Dc Motors &
Drives. Reconditioned with 2 Cold Wire Feeders or Converted to Mig
Welding Including Power Sources
1 ea WS406001 Pandjiris Model
SWPT-102 Dual Side Beam Stiffener Welder. HD Welding Carriage,
variable speed (0 200 IPM). Twin Cyclomatic Seam Tracking systems
to locate torches on opposing sides of stiffener. Open-End Gantry
Style Yoke with 96" of Weld Length allows loading of stiffener
from one end. Advancement of sheet is readily done with help from
pneumatic plate lift rollers that automatically lift part off back-up
bar between welds. 15 Pneumatic hold down Clamps and Part Locators
designed to automatically locate and hold "I" or
"U" shape stiffener in place on sheet. No tooling or jigs
necessary for part alignment. Back-up Bar for heat sink and part
distortion control. System is capable of feeding Aluminum or Steel
Wire using GMAW Process. Twin 180 degree water-cooled GMAW torches for
high production. Remote Control Podium. Was used for welding
stiffeners for aluminum dump truck beds and bodies. Very unique piece
of equipment Must See!!! Very Good Condition
1 ea WS411001 Linde PTA Surfacing
System / 5 x 6 Manipulator. A Complete Linde Plasma Transfer Arc Weld
Surfacing System that Includes a C75-500 (500 amp, 60% Duty Cycle)
Power Supply, PTA Gun, Automatic Powder Feeder, 12 Manual Vertical
Adjuster, and a Linde Solid State Weld Oscillator. Gun, Vertical
Adjuster, Powder Feeder and Oscillator are Mounted on a Linde OM-48
Variable Speed Travel Car that Runs on a Fixed Boom Manipulator with
6 of Horizontal Travel and 60 of Vertical Travel from 31 to
91 by a Screw Driven Manual Hand Wheel Lift. Good Working Condition
1 ea WS408001 Compak-o-Matic
Rotary Welding Station. System Includes a Ransome B-100, 100 lb
Capacity Welding Positioner, A Compak-o-Matic PC-300, 300 amp CV Power
Supply, a Model 320 Wire Feed System with a Machine Torch, 8
Horizontal and Vertical Torch Adjusters, and Model 263 Control Module
with Weld Time Function. Serial #1530 Good Condition
1 ea WS412001 Jetline Portable
Heavy Duty Cast Long Length Stellite Overlay System. Jetline
TKK-24 Precision Screw Drive (1-1/2 screw) Side Beam with 24
Travel. Heavy Duty 9-1/2 Power Vertical Slide, 8 of Z axis
Manual Slide. Long Rod Feeder with adj. dia. guide. Miller Oscillator
with Center Line Steering. Overall dimensions of Portable side Beam
Assy. 76 high, 63 wide, 60 long. System includes Miller 300
amp Synchrowave welder and Tig Torch. Excellent Condition!
1 ea WS999001 Linde/Jetline HWC-7
Cold Wire Tig System. Jetline ZB-100 Positioner on moveable screw
drive base. Complete with HW-500SS Welder, Auto Controls, Cross Slides
and Floor Standing Base. Excellent Condition
1 ea WS006003 Hobart/Aronson 2
Station Automatic Spud Welder. Mig Welds Rings up to 12 Diameter,
Two alternate weld stations w/ Air Clamping of parts. Control Console
w/ Station Selection. Many Tooling Fixtures. Var. Speed Rot. by 2
Aronson positioners. Includes Hobart Dual Wire Feeder, Torches and
Welder. Complete System Ready to Weld
PANASONIC
ROBOT WELDING CELLS - USED ROBOTS
1 ea RC505001 "2003" Panasonic 3 Axis Model ISP
Cartesian Robotic Tig Welding Cell. Initially powered up in
November 2003 this cell was used off and on for approximately 8 months
before the application was discontinued. This Panasonic Model ISP
Cartesian Robot, has approx. 43" (x) horizontal movement,
15" (y) vertical movement and 21" (z) horizontal movement.
There is also a 2 axis clamping fixture or tooling table. The complete
welding package on this cell includes Two (2) Water Cooled Tig Torches
with manual adjustable separation of the torch holders on one axis,
Two (2) Panasonic YC-500WX4 Power Supplies completely integrated with
all regulators, hoses, cables etc. Water supply required. The welding
cell is 75" wide x 103" high x 145" deep and has a
complete safety package including, Powered Safety Screen, Light
Package, Front Operating Control and Palm Buttons. This cell could
be changed to the Mig welding process. This is a late model, low hour,
system in Excellent Condition
1 ea RC505002 "2003" Panasonic 4 Axis Model ISP
Cartesian Robotic Tig Welding Cell. Initially powered up in
November 2003 this cell was used off and on for approximately 8 months
before the application was discontinued. This Panasonic Model ISP
Cartesian Robot, has approx. 17 1/2" (x) horizontal movement,
10" (y) vertical movement and 15" (z) horizontal movement.
The Fourth Axis is a Rotating Wrist movement for the Torch Holding
Device. This Cell also includes a Horizontal Moving Fixture/Tooling
Table Integrated with the Robot from the Load/Unload position to the
Robotic Welding Position. The Complete Welding Package on this cell
includes one (1) Panasonic YC-300WX4 Power Supply and One (1) Water
Cooled Tig Torch completely integrated with all cables, hoses, etc.
Water supply required. The welding cell is 75" wide x 103"
high x 126" deep and has a complete safety package including,
Powered Safety Screen, Light Package, Front Operating Control and Palm
Buttons. This cell could be changed to the Mig welding process.
This is a current model, low hour, system in Excellent Condition
1 ea RC505005 "2003" Panasonic VR-008 GII Robotic, 6
Axis Tig Welding Cell. This is a larger, panel constructed,
Robotic welding Cell with a large Fixture/Tooling table that has
approx. 78" of in and out movement between load and welding
stations. The Complete Welding Package on this cell includes one (1)
Panasonic YC-300WX4 Power Supply, One (1) Water Cooled Tig Torch
complete with all cables, hoses, etc. Water supply required. This
Welding Cell accomodated this Panasonic VR-008 GII Robotic System and
the "2003" Motoman UP-50 listed and priced separately below.
See the picture of this larger panel constructed cell for
approximation of size. This is a Current Model, Low Hour System, in
Excellent Condition! Price includes Panel Constructed Cell.
1 ea RC505004 "2003" Panasonic Robotic VR-008 GII, 6
Axis Tig Welding Cell. The Fixture/Tooling Platform is on an
Integrated Horizontal Travel Part Presentation Carriage with 26"
of Movement from the Load/Unload Station. This system provides
maximum operator access for load/unloading and increased productivity.
The Complete Welding Package on this cell includes one (1) Panasonic
YC-300WX4 Power Supply, One (1) Water Cooled Tig Torch complete with
all cables, hoses, etc. Water supply required. The welding cell is a
completely enclosed 102" wide x 103" high x 172" deep
structure with side access doors and a complete safety package
including, Powered Safety Screen, Light Package, Front Operating
Control and Palm Buttons.
This is a Current Model, Low Hour System, in Excellent Condition
1 ea R510001P Motoman Model YRFL-NND10G 6-Axis Robot.
22 lb
Payload Capacity. Robot Controller NOT Included. "1986"
Serial #RH9963-6047-8 "As-Is" Only
1 ea R510011P Miller/OTC Model MRV-6 6-Axis Welding Robot.
13.2
lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1
Control Cabinet. Welding Equipment NOT Included. "1991".
190-575 Volt. Serial #KB168739 "As-Is" Only
1 ea R510012P Miller/OTC Model MRV-6 6-Axis Welding Robot.
13.2
lb Payload Capacity. 55.2" Reach. Includes a Miller Model C-1
Control Cabinet. Welding Equipment NOT Included. "1992".
190-575 Volt. Serial #KC301838 "As-Is" Only
1 ea WS605013P Cybotech Automatic Manipulator / Positioner Tig
Welding System. System Includes A Fabspec 2,500 lb Capacity
Positioner, a 6 Axis Cybotech 4 X 3 Manipulator / 6 Travel
Car, Cybotech RC-6 Controller, Cold Wire Feeder, Miller Syncrowave 300
w/ SP-4 Pulser. System Offers 9 Axis of Powered Movement. Good
Condition
1 ea WS605014P Cybotech Automatic Manipulator / Positioner Tig
Welding System. System Includes A Fabspec Model 1840 2,000
lb Positioner, a 6 Axis Cybotech 4 X 3 Manipulator / 6 Travel
Car, Cybotech RC-6 Controller, Cold Wire Feeder, Cybotech EPU Power
Supply. System Offers 9 Axis of Powered Movement. Good Condition
ROBOTIC TURNTABLES & POSITIONERS
1 ea RP612017 Preston-Eastin Model
RHSDS-5 Dual Sided Robotic Headstock/Tailstock. Dual sided for loading
/ unloading on one side while welding on the other. Shot pins for
precise positioning. 500 lb balanced load capacity on each side. 6
length capacity. 24 diameter capacity. Dual Allen-Bradley SLC-150
controls, one for each of the headstock/tailstocks. Serial #RHDS-5-6
Good Condition As-Is Only
1 ea RP612018 Preston-Eastin Model
RHSDS-5 Dual Sided Robotic Headstock/Tailstock. Dual sided for loading
/ unloading on one side while welding on the other. Shot pins for
precise positioning. 500 lb balanced load capacity on each side. 6
length capacity. 24 diameter capacity. Dual Allen-Bradley SLC-150
controls, one for each of the headstock/tailstocks. Serial #RHDS-5-10
Good Condition As-Is Only
1 ea RP004002 ABB/Esab Orbit 160B,
Robotic Positioner. Two Station Articulating Positioner, for Load
& Weld Station. 353 lbs Each Side, Table Rotation 90 Deg. in 2.7
Sec. Or 360 Deg. in 6.8 Sec., Tilting Arm: Turning Speed 0 to 11.8
RPM, Indexing 90 Deg. 2.7 Sec., 360 Deg. 7.2 Sec., Station Interchange
3.5 Sec. This unit was integrated to ABB/Esab a IRB 6L2 Robot. Pos.
Ser.#414 441 9034, Cont. 443 440 9005
1 ea RP307001 Aronson Ride-5,
Double Ended Tilt and Rotate Robotic Indexing Positioner. This
Two-Station Tilt/Rotate Positioner has a Capacity of 500 lbs per Table
@ 6" C.G. Tilt and 3" C.G. Rotation. 180 Degree Sweep in 7
Seconds with .0001 Repeatability. Two 18" Diameter Tables with
Slots. 8 Non-Adjustable Index Stops for the Table Rotational Axis. 4
Non-Adjust6able Index Stops for the Tilt Axis. Can be Connected to any
Robot with Compatible I/O. This is an Indexing Type System, Not Servo.
Serial #843 Good Condition
1 ea RP210003P Koike-Aronson
RHS10/T2.5-30SD Robotic "Skyhook" Positioner. 2500 lb Load
Capacity. Center of Gravity 28". Overhang 3". Off-Center
38" Table. Backlash Control and "Zero" Indicator on
Control. "Skyhook" Positioners Provide Part Rotation in Two
360 Degree Axis which Result in Partial or Full Inverting of the Work
piece. Serial #869 Very Good Condition
1ea RP207001 Preston-Eastin Model
DEPA-30FB Robotic Positioner. Two Station Articulating Positioner, for
Load & Weld Station. 3,000 lb Capacity @ 6" C.G. Each Side.
Fixed Table Height of 48" with the Table Flat. 43" x
43" Square Work Tables. Servo Drive that can be Installed on any
Robotic System with the Proper Relays. "1996" Serial
#DEPA-30FB-187 Priced As-Is !! Ready to Install Your Servo Motors and
Controls !! Very Good Condition
1 ea RP809023 Aronson
RDE-RHS10/T3-42SD Double Ended Robotic Skyhook Positioner. A two
station articulating positioned for loading and weld station. Each
side has a capacity of 3,000 lb @ 18 c.g., 12 off set tables
from the center of the horizontal rotational axis. 36 diameter
round tables with 8.25 thru holes. Serial #882 AS-IS Only
1 ea RP809024 Aronson
RDE-RHS10/T3-42SD Double Ended Robotic Skyhook Positioner. A two
station articulating positioned for loading and weld station. Each
side has a capacity of 3,000 lb @ 18 c.g., 12 off set tables
from the center of the horizontal rotational axis. 36 diameter
round tables with 8.25 thru holes. Serial #881 AS-IS Only !!
1 ea RP309001P Koike-Aronson
1994 Model #RDCG/T6-100/26SD Drop-Center Positioner. Tilt
Capacity of 6600 lbs @ 24 from the table, or 4000 lbs @ 57, or
2000 lbs @ 90!!. Rotation Capacity of 6600 lbs @ 20 Center of
Gravity off of the centerline of rotation. Inside Distance Between
Upright Sides is 101-3/4 Both Tilt and Rotation Axis have
Adjustable Anti-Backlash Dual Pinions on Bull Gears! Both Axis are
Servo Drive Variable Speed with Encoders and Resolves. 360 deg.
Rotation @ 0.0-2.0 RPM, 200 deg. Tilt @ 0.0-1.75 RPM. (This Servo
Drive Positioner can be converted to a Manual Pendant Operated
Machine). Table is 48 x 48 with Hydraulic Master Clamping System
for Slave Pallet Mounted Tooling 1 ea. slave included . Note; Drop
Center Positioners are typically used for work pieces with longer
Center of Gravity distances from the table, resulting in lower working
or welding heights than using higher capacity positioners. This 1994
Machine has NEVER BEEN USED! Brand New Condition!
1 ea. M404001 Precision 9 x
9 x 27-1/2 Heavy Duty Manipulator/Travel Car System. This system
was manufactured for the Robotics Industry for precision welding on
military vehicles. Heavy Duty Mast has 9 ft. of constant speed of
precision screw driven lift starting at approx. 36 from the floor
to 144 high under the boom. The mast has manual rotation with lock.
Boom has 9 ft. of Dual Pinion variable speed gear drive and
rolls on Thompson Round way roller system. Weight capacity approx. 750
lb. Travel car is 5 x 5 x 19 High and Variable Speed Rack
& Pinion Drive on 33 ft. of Thompson Roundway Precision Track. All
three (3)-axis paths are accordion booted. This system is now Servo
driven. We will change to Pendant AC-Inverter or D.C. Drives. Very
Good Condition
AUTOMATION
WELDING ACCESSORIES
6 ea AA310001 Computer Weld Technology ADM III Arc Data
Monitoring System. The CWT Arc Data Monitor is a Self-Diagnostic
Microprocessor System Designed to Provide Quality Control for Arc
Welding Applications. Each System Includes Sensors and Cables to
Monitor the Following Parameters: Arc Voltage from 0 to 100.0 Volts DC
+ or - 1%, Arc Current from 0 to 1000 Amps DC + or - 1%, Gas Flow from
5 to 255 scfh + or - 1% and Travel Speed from 1 to 100 ipm + or - 3% Very
Good Condition
7 ea AA310002 Computer Weld Technology ADM III Arc Data
Monitoring System. The CWT A rc Data Monitor is a Self-Diagnostic
Microprocessor System Designed to Provide Quality Control for Arc
Welding Applications. Each System Includes Sensors and Cables to
Monitor the Following Parameters: Arc Voltage from 0 to 100.0 Volts DC
+ or - 1%, Arc Current from 0 to 1000 Amps DC + or - 1% and Gas Flow
from 5 to 255 scfh + or - 1% Very Good Condition
RESISTANCE WELDING EQUIPMENT
1 ea SP103523 Taylor Winfield 70 KVA,
Equalizing Rocker Arm Welder. "1996" Very Little Use! Mach.
#960180. 70 KVA, 460V. 20"Depth, Water Cooled, Self Equalizing
Arms, High Production System with Quick Manual Part Indexing for
Rotation and Forward- Back Feed. These machines (we have 3) were
designed for production welding of washer/dryer tubs. "1996"
Excellent Condition
1 ea SP103524 Taylor Winfield 85 KVA,
Equalizing Rocker Arm Welder. "1996" Very Little Use! Mach.
#960177. 85 KVA, 460V. 20"Depth, Water Cooled, Self Equalizing
Arms, High Production System with Quick Manual Part Indexing for
Rotation and Forward- Back Feed. These machines (we have 3) were
designed for production welding of washer/dryer tubs. "1996"
Excellent Condition
1 ea SP103525 Taylor Winfield 85 KVA,
Equalizing Rocker Arm Welder. "1996" Very Little Use! Mach.
#960179. 85 KVA, 460V. 20"Depth, Water Cooled, Self Equalizing
Arms, High Production System with Quick Manual Part Indexing for
Rotation and Forward- Back Feed. These machines (we have 3) were
designed for production welding of washer/dryer tubs. "1996"
Excellent Condition
PLASMA WELDING EQUIPMENT
PW310001 Thermal-Arc PS-3000 Plasma Welding System
Complete. Each System to Include the Following : PS-3000 Power
Supply with an Output Range from 5 to 350 amp 300 amp 60% Duty Cycle
208/230/460 volt 1 or 3 Phase, WC100B Weld Control Console, HE-100A
Water Cooler, Weld Sequence Package with WT-1 Weld Timer, Cs-1 Current
Sloper and CP- Pulser, #870119 Interface Cable and a 180 degree Offset
Model 4A 12.5' Plasma Machine Torch, 220 amp, 60% Duty Cycle Very
Good Condition
PW310002 Thermal-Arc Ultma 150 Plasma Welding System. A Self
Contained Package with a 150 amp, 50% Duty Cycle Power Supply, Coolant
Circulator and Control Console. 200-460 VAC, 1 or 3 Phase, Welding
Torch NOT Included. Optional Sequencer console with timer, slope,
pulse is available, price upon request. Excellent Like New Condition
Condition OR - Optional Weld Sequencer Timer, Pulse,
Slope.
METCO, PLASMA SPRAY & PLASMA
TRANSFER ARC EQUIPMENT
PS810027 Stellite Coatings Starweld
Plasma Arc Transfer System. System includes a Stellite Starweld II
power supply console, gas control panel, X,Y and Z motorized slide
assembly, torch oscillator, torch angle assembly, Variable speed
headstock with pneumatic tailstock assembly, center support roller
assembly, control pendant with touch screen, refrigerated torch water
cooler, model KK-2 powder feeder, model 600 torch and complete cable
and hose package. Sold new in 2000 for over Very little use.
A Must See !!!! Excellent Condition Priced As-Is
1 ea PS709004P Metco Model AR-2000
6-Axis Thermal Spray Robot. A complete robotic system that includes a
Metco AR-2000 6-axis robot with controller, a Metco teach pendant, a
Metco R-2 operating box and a set of connecting cables. Serial
#AR110001 AS-IS Only
1 ea PLA PS61S Plasmatron Model
PS-61S Plasma Power Supplies. Ser.# JD-683762 & Ser.# JC- 586408,
1000 amps @ 40 volts or 500 amps @ 80 volts, 74 K.V.A., Input
200/230/460 Power Factor Corrected. Very Good Condition
CUTTING & WELDING EQUIPMENT
CM809007 Bug-O Uni-Bug II Self-Guided Cutting System.
The
Uni-Bug II will carry a torch into very tight area or around very
tight curves without the use of a track. Can cut straight line or
radii as small as 6. Variable speed travel from 4 to 75 ipm.
Designed to run on the edge of a bar or stiffener up to 2 thick.
120 volt. Serial #0620900. Good Condition
CM808014 Koike Model KHC-600D Portable Pipe Oxy/Fuel
Hole Cutting Machine. 3.5 to 23 hole cutting diameter
range. 0-4 rise and fall torch lift. Rotating gas manifold. Can be
used to cut holes in pipe, vessels or flat plate. Includes cutting
torch. 115 volt. Serial #053811.Purchased NEW in June, 2007
NEVER USED
CM808015 Koike Model KHC-600D Portable Pipe Oxy/Fuel
Hole Cutting Machine. 3.5 to 23 hole cutting diameter
range. 0-4 rise and fall torch lift. Rotating gas manifold. Can be
used to cut holes in pipe, vessels or flat plate. 115 volt. Includes
cutting torch. Serial #053815. Purchased NEW in June, 2007
NEVER USED
1 ea CM303001 Linda Shapemaker 48" Template Cutting
Machine. Magnetic Template Tracing Contour Cutter. Size Capacity
is any Shape that will fit in a 48" Circle. Has a Push Button RC
Control. Floor Model on "H" Base. No Torch or Cutting
Equipment Included. Serial #0351-18 Good Condition
1 ea Linda "Cadet" Oxy-Fuel Portable "Hand
Held" Cutting Machine with Circle Attachment
1 ea Bug-O, Speed Weaver , with Two motion Torch Holder ,
18" Rack, Fits All clamp. Mounted on Floor Stand. Very Good
Condition
1 ea Bug-O, "Con-O" 5, Contour Saddle Cutter.
Ser.#
8961 For Cutting and Beveling saddle holes in pipe. Capacity 18"
to 30" diameter holes. Complete with Torch
H & M Pipe Beveling Machines!! From 2" diameter
pipe to 36". All Machines are complete. We Have Both Motorized
and Hand Crank Units. CALL FOR PRICES
FABRICATION MACHINERY
1 ea FAB701006 Whitney 4" x 4" x 3/16" Hydraulic
Angle Iron Shear. Shear with hydraulic cylinder mounted in a bench
mount frame. Hydraulic pump NOT included. Serial # N/A Good
Condition
1 ea ME408007 Gullco Plate Beveler Model BCM-12. 5/8"
Capacity. Mounted on Roller Base Stand. 230/460 volt. 3-phase. Serial
#71382-1 Good Condition $ 3,950.
1 ea FAB611011P Comaca Model N225 Uninotch Universal Notcher.
8.5"
x 8.5" x 1.56" Capacity. Equipped with T-Slotted Cast Table,
Pneumatic Gauges, Automatic Feed, Swing Down Blade Guard, Remote Foot
Switch, Hydraulic Pump Motor and Electric and Air Controls. Serial
#N/A Good Condition
JUST SOME OF OUR WELDING &
MISCELLANEOUS ITEMS
1 ea VC802003P Airline Model VC-48
Vacuum Chamber. 48" diameter x 24" high welding chamber.
38" high work table. 2 sets of vacuum glove ports. Includes a
vacuum pump, vacuum gauge and inert gas flow-meter with pressure
regulator. Serial #193 Good Condition
1 ea VC704016 Jetline Model VC-48Z
Vacuum Welding Chamber. Chamber is 48" diameter x 24" high
with a transparent domed removable top. 39" high work table.
Includes 2 pair of 8" diameter glove ports, vacuum pump, vacuum
gauge, inert gas flowmeter with pressure gauge. Serial #900441
Excellent Condition
1 ea VC701002 Vacuum Atmospheres
Corporation Model HE-233-62 Vacuum Chamber. 96" long x 42"
wide x 32" high vacuum / welding chamber. 39" high work
table. 5 glove ports on both sides of the 8 length. Includes a
Vacuum Atmospheres Corp. Model HE-373-BIN (Serial #50517-464) 300
degree, 800 watt drying furnace. Serial #20922-1 Good Condition
1 ea ME702001 Elmatco Degaussatron
Dual Loop Demagnitizer. Complete dual coil demagnetizing system that
includes a model VCFNR50 Control, 2 each model L1S6-24X24 coils, 2
each support cradles and track. 208/230/380/415/460 volt 1-phase.
Serial #9065521X,9065551X & 9065550X Very Good Condition
1 ea ME704010 Arc-Air Model N-6000
Automatic Gouging System. 1600 amp capacity. Accepts gouging
electrodes from 5/16" to Ύ" diameter. System includes torch
head, automatic controller, 1600 amp contactor, power cable assembly
and interconnecting cable assembly. Requires 60 to 100 psi compressed
air (45 to 80 cfm). 120 volt. Serial #1237 Very Good Condition
1 ea FAB611006P 36" x 58"
Scissor Lift Table. Equipped with casters for ease of movement. Good
Condition
1 ea ME611016 Torit / Donaldson Mini
Trunk 2 gun fume exhaust system. 150cfm nominal air flow. 6.7HP motor.
460 volt, 3-phase. Serial #IGS88000-2 Good Condition
1 ea ME611008P Aerocology Model
CFP-1500F Portable Dust Collector. 18.75" wide x 42" deep x
65" high on floor mount casters. 3HP motor. Equipped with two
cartridge filters, air blast cleaning and dust drawers. 460 volt,
3-phase. Serial #43920 Good Condition
1 ea WE301001 Linda Twin Wire Overlay
Head. Linda Twin Wire Feed Head with 90 Degree 48" Contact Tube
Assembly and 2" Mechanical Weld Oscillator. Used for External
Overlay or Internal Overlay of Cylinders Over 12" I.D. Good
Condition
1 ea ME209009 GE Type MC-6A Power DC
Circuit Breaker. 750 Volt. 12,000 Amp. Manual Operated. Serial
#196A1956-90-GB Very Good Condition
1 ea ME205001 Thermco Model
6205CA30A1100 Gas Mixer. 0 - 30% CO2 in Argon. Capacity of 0 - 5000
PSIG. 100 - 125 PSIG Inlet Pressure. 10 - 50 PSIG Outlet Pressure. 60
Gallon Surge Tank. With Gas Analyzer and Optional Alarm System. 115
Volt. Serial #18381 Excellent Condition
FEATURED AUTOMATED
WELDING SYSTEMS DETAILS
1 ea WS509001 Pandjiris 1998
Hot Wire Tig Pipe Welding Station. A Complete Hot Wire Tig Pipe
Welding Station that Includes a Pandjiris 4 x 4 Manipulator on
Travel Car, 2 each Pandjiris HS-20PE-VS Headstocks with TJ-20 Chucks,
Pandjiris Pipe Supports on Manual Travel Cars, Miller / Jetline
Welding Package and a Complete set of 50 Tracks. Please Ask for a
Detailed Specification Sheet. Excellent Condition !!
Specifications and Features :
Manipulator :Pandjiris Model 88.
4 Variable Speed Elevation (3 to 73 IPM) from 20-1/2
to68-1/2. 4 Variable Speed Reach (3 to 110 IPM) from 21 to
69 from the Center of the Column. Powered Mast Rotation with Limits
for 180 Degree Indexing from One Headstock To the Other. Mounted on a
Pandjiris Model 3042 VSC Variable Speed Travel Car and 50 of 42
Gauge Track. Also Has a Welder Platform to Carry all the Welding
Equipment with the Travel Car and Spring Style Electric Cable Reels
Mounted on Travel Car. Serial #12223ECO
Headstocks: 2 each Pandjiris Model
HS-20-VS-PE. 2,000 lb Capacity @ 5 C.G., Variable Speed Rotation
from .07 to 1.4 RPM. 12 Power Elevation from 33 to 45 to the
Center of the Rotational Axis.
Both Headstocks are Equipped with
the Following Options :
Pandjiris TJ-20 Quickset Gripper
Chuck, 1 to 16-1/2 Outside Clamping Capacity, 6-1/4 to 20
Inside Clamping Capacity.
Pandjiris Dialweld Control
Shows Linear Speed in IPM for Diameter Set on Selector Dial
Diameter to Welded, Dial Weld Speed, and the Table RPM is
Automatically set to Weld Diameter at a Selected Welding Speed.
3 Each Heavy Duty Roller Head Pipe
Supports on Manual Travel Cars that sit on 50 of 24 Gauge Track
Welding Equipment :
1998 Miller Phoenix 456
CC/CV Power Supply, 450 amp, 100% Duty Cycle, Serial #KJ079755
Miller HF-20-1WG High Frequency
Unit
Bernard 3500 Water Circulator
Weldcraft WP-27B 500 Amp Water
Cooled Tig Torch
1998 Jetline Model 9500
Micro Processor System Control Serial #980394
1998 Jetline ALC-201-V6T Arc
Length Control with 6 Slide Serial #980198
1998 Jetline Model 9200 Weld
Oscillator Serial #980395 with a 9032-47105 Oscillator Programer
Control for Storing up to 4 Programs Serial #980395
2003 Jetline Model 98028 Hot
Wire Tig Feeder Control Serial #030111 and a HWP-200D Hot Wire Tig
Power Supply, Torch & Wire Delivery Bracket
Thermal arc HE-150 Water Coolant
Circulator
3 Vertical Cross Slide
1ea S910004P Amet / Jetline 8
Vertical Variable Polarity Seamer. System includes an Amet controller
& operating console, Amet Motor control center, An integrated Amet
500 VP power supply, Custom gas control unit, 8 x 8 manipulator
and 8 vertical seamer bed, 4-roll wire feeder and all welding
equipment. Purchased New in 2002 for OVER $300,000.00 !! Please Ask
for a Detailed Specification Sheet !! Excellent Condition !!
As-Is Price !!
Specifications and Features :
Amet Controller and Opperator
Console :
Graph Editor Graphical weld schedule creation and administration
software.
Control of 4 servo axis (2-axis torch cross slide assembly for
mechanical oscillation &AVC, wire feed and vertical travel.
Integrated Automatic Voltage Control
VPPA System monitoring software
Calibration and diagnostic software
Operator access control and logging.
15 Flat Panel LCD color display
Keyboard and mouse in a retractable drawer
Remote pendant with stand
System fault interlocks and indicators
Amet Motor Control Center :
4 axis pulse width modulated DC motor amplifiers
DC power supply
Limit switch sensing
Emergency stop sequencing
Power Supply Amet 500 VP supply with integrated :
500 amp, 100% duty cycle
Plasma pilot arc console / drawer
Computer interface drawer
Hour meter panel
Enclosed fusing, GE transformer & disconnect
Custom Gas Control Unit :
3 mass flow controllers, 3 mass flow meters
3 gas solenoids
Integrated with Advent System
Manipulator & Part Fixturing :
8 x 8 welding window
Vertical seam welding part positioning fixture
Weld head locator (8 x 8 travel) motorized precision round way /
screw feed
DC servo controlled vertical beam travel
Motorized horizontal control
Cable management system
Integrated with remote pendant
Precision Torch Positioner Includes :
X axis torch slide (12 travel)
Z axis torch (AVC) slide with DC servo
Torch mounting hardware
Integrated with remote pendant
Wire Nozzle Positioner Includes :
Motorized two axis nozzle positioned
Nozzle mounting bracket
Integrated with remote pendant
Wire Feed Unit Includes :
Heavy duty 4 roll wire drive system
Servo motor with encoder
Capable of driving .030 to .060 diameter wire
Welding Equipment Includes :
B & B Plasma torch and cables
Dynaflux water circulator and system integration
1 ea S910003P Pandjiris / Hobart
8 Vertical Variable Polarity Seamer. System includes an integrated
Hobart VP-300S power supply, gas control unit, 8 x 8 manipulator
and 8 vertical seamer bed, 4-roll wire feeder and all welding
equipment Please Ask for a Detailed Specification Sheet !! Very Good
Condition !!
Power Supply Hobart VP-300S
Variable Polarity Power Supply :
300 amp, 100% duty cycle
Plasma pilot arc control
Custom Gas Control Unit :
3 mass flow controllers, 3 mass flow meters
3 gas solenoids
Manipulator & Part Fixturing :
Vertical seam welding part positioning fixture
Weld head locator (8 x 8 travel) motorized precision round way /
screw feed
Motorized horizontal control
Cable management system
Integrated with remote pendant
Precision Torch Positioner Includes :
X axis torch slide (12 travel)
Z axis torch (AVC) slide with DC servo
Torch mounting hardware
Wire Feed Unit Includes :
Heavy duty 4 roll wire drive system
Capable of driving .023 to .062 diameter wire
Welding Equipment Includes :
Plasma torch and cables
Dynaflux water circulator and system integration
